Instant quote across 18 Volvo V60 variants in under 60 seconds, fitted by approved fitters — booked in under two minutes.
Make
Volvo
Model
V60
No card required · Free to quote
Prices vary with generation and ADAS equipment — earlier V60 models without cameras or heating are typically more affordable, whilst later variants with integrated mono cameras, heated zones, and LIDAR-compatible glass carry higher calibration costs. Acoustic glass and heat-absorbing PVB interlayers (common on higher-spec variants) also influence the final quote, as does encapsulation (factory-bonded gasket trim) which arrives as a complete unit.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2026 | £708 — £1,203 | 7 variants | Price my 2026 |
| 2025 | £708 — £1,203 | 7 variants | Price my 2025 |
| 2024 | £708 — £1,203 | 7 variants | Price my 2024 |
| 2023 | £708 — £1,203 | 7 variants | Price my 2023 |
| 2022 | £708 — £1,203 | 8 variants | Price my 2022 |
| 2021 | £708 — £1,203 | 8 variants | Price my 2021 |
| 2020 | £708 — £1,203 | 8 variants | Price my 2020 |
| 2019 | £708 — £1,203 | 8 variants | Price my 2019 |
| 2018 | £480 — £1,203 | 14 variants | Price my 2018 |
| 2017 | £480 — £939 | 7 variants | Price my 2017 |
| 2016 | £480 — £939 | 7 variants | Price my 2016 |
| 2015 | £480 — £939 | 7 variants | Price my 2015 |
| 2014 | £480 — £939 | 7 variants | Price my 2014 |
| 2013 | £480 — £939 | 7 variants | Price my 2013 |
| 2012 | £462 — £939 | 11 variants | Price my 2012 |
| 2011 | £462 — £939 | 9 variants | Price my 2011 |
| 2010 | £462 — £939 | 9 variants | Price my 2010 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older V60s can still be booked.
Curious why prices vary so widely? Read our UK windscreen replacement cost guide .
Reviews below are hand-picked from recent UK customers. Across the whole of UK Car Glass, 4.82/5 from 1,422 Trustpilot reviews.
Booking your V60 windscreen replacement through UK Car Glass is straightforward and takes just a few minutes.
Answer a short online quiz about your model year and trim — this identifies your exact windscreen variant and any ADAS or heating features.
Receive an instant quote matched to your V60's specification.
Book your preferred date and time; you'll be matched with a specialist near you.
On fitting day, your technician will inspect the windscreen frame, set the replacement glass, and if your V60 carries a mono camera or LIDAR system, arrange any required calibration (typically at a workshop to ensure accuracy).
Your fitter confirms the drive-away time before releasing the vehicle — calibration runs in parallel with adhesive cure, so it doesn't extend the time before you can drive.
You're covered by a two-year warranty on workmanship and glass quality.
Most V60 windscreen jobs complete within a couple of hours, with times varying based on your specific variant and calibration needs.
Most V60 windscreen replacements can be done at your home or workplace as a mobile visit. However, if your V60 carries a mono camera or LIDAR system (increasingly common from 2018 onwards), static camera calibration is required after the glass sets, and this must be completed at a workshop with specialised target boards.
When calibration is needed, the entire job — replacement and calibration together — is scheduled at a workshop location to ensure the work is completed in one session and you have control over whether safety-critical calibration actually happens. Your technician will confirm this when you book.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.
Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.
The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.
Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.
Your wipers automatically activate when rain falls on the windscreen.
A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.
Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.
Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.
Factory-bonded rubber or polymer trim means your replacement glass arrives ready to fit as one complete unit.
Encapsulation is a rubber or polymer gasket moulded directly onto the glass edges during manufacturing. The trim is bonded to the glass at the factory — either by injection moulding, PU robot extrusion, or adhesive bonding. When you need a replacement, the entire panel arrives with its trim already attached, so the glass and gasket are replaced together as a single unit rather than as separate components.
Check your current windscreen or rear window edges. If you see a continuous rubber or polymer seal running around the perimeter that appears moulded or permanently bonded to the glass itself — rather than a separate trim clipped or screwed to the frame — your glass is encapsulated. Ask your dealer or service centre to confirm; they can also check your vehicle specification sheet.
Encapsulated glass simplifies replacement because there's no separate trim to remove, refit, or source. The bonded gasket is replaced as part of the glass unit, which reduces installation complexity and potential leak points. Cure time and drive-away procedures remain unchanged. No additional sourcing delays — encapsulated replacements are stocked as complete assemblies by most suppliers.
LIDAR helps your car sense its surroundings for advanced safety and driver-assistance features.
LIDAR (Light Detection and Ranging) is a sensor technology that uses laser beams to detect objects, obstacles, and road features in three dimensions. It creates a detailed map of the vehicle's surroundings in real time, enabling advanced driver-assistance systems (ADAS) such as adaptive cruise control, collision avoidance, and autonomous emergency braking. LIDAR complements camera and radar systems by providing precise distance and depth information, even in poor visibility or low-light conditions. It is increasingly fitted to modern vehicles as part of their safety and autonomous-capability infrastructure.
Check your vehicle's handbook or contact your dealership to confirm LIDAR fitment. LIDAR sensors are typically mounted on the roof, bumpers, or within the windscreen/rear-window frame area. You may see reference to 'LIDAR', 'laser radar', or specific safety-feature names (e.g. 'adaptive cruise control', 'autonomous emergency braking') that rely on LIDAR in your documentation.
If your windscreen or rear window houses or frames a LIDAR sensor, replacement requires careful handling to preserve or recalibrate the sensor post-fit. LIDAR calibration procedures vary significantly by vehicle make, model, and year—some require static alignment using specialist target equipment, others demand dynamic road-drive procedures, and some use a combination. We identify the exact calibration requirement when we look up your specific vehicle and confirm it with you before booking.
A modified black-printed area around the rear-view mirror to suit your vehicle's camera or sensor layout.
Silkscreen modification refers to a variation in the black-printed area (called the 'frit') that surrounds the rear-view mirror on your windscreen. This printed zone is shaped to accommodate your vehicle's specific camera, sensor, or ADAS equipment layout. Different vehicles — even within the same model range — may have different camera positions or sensor configurations, requiring a bespoke print pattern. A silkscreen-modified windscreen is a distinct part with its own part number and cannot be used interchangeably with the standard print variant.
Check your windscreen documentation or the original part number — dealership service records will confirm whether your windscreen carries a modified silkscreen. You can also ask your dealer's parts department to confirm the exact print variant for your vehicle's year and specification. The modification itself is visible as the black-printed border around the mirror area, but identifying whether it's 'modified' requires checking the part number rather than visual inspection alone.
When your windscreen requires replacement, we must source the correct silkscreen variant for your specific vehicle to ensure proper camera and sensor clearance. Using an incorrect print variant could obstruct camera fields of view or interfere with sensor operation, compromising ADAS functionality and safety. We confirm the exact part number during the booking process to guarantee the correct glass is supplied and fitted. No additional calibration is triggered by the silkscreen modification itself; any calibration needed relates to the camera or sensor system, not the print.
Pre-fitted clips and brackets that secure the glass to your vehicle, supplied ready to bond as a complete unit.
Fitting hardware comprises the clips, brackets, mouldings and adhesive retention components that hold the glass securely in place on your vehicle's frame. When your replacement glass is supplied with fitting hardware pre-attached, it arrives as a ready-to-install assembly rather than as bare glass requiring separate hardware attachment during the fit. This streamlines the replacement process and ensures correct positioning and fitment.
Check your vehicle's service history or contact your dealership service department with your registration number. They can confirm whether your glass comes with pre-fitted hardware as standard. Visually, pre-fitted hardware appears as clips or brackets already bonded or attached to the glass edges before it reaches the fitting technician.
Glass supplied with pre-fitted hardware typically requires no additional labour to attach clips or brackets during the fit, reducing technician time at the vehicle. The hardware must be in good condition and correctly positioned for the glass to seal and function properly. If hardware is damaged during removal of the old glass, replacement or repair of that hardware may be needed before the new glass can be fitted securely.
Acoustic glass reduces cabin noise for a quieter, more comfortable ride.
Acoustic windscreen glass is laminated with a special acoustic interlayer that absorbs and dampens sound vibrations. It reduces exterior noise—from traffic, wind, and road surface—before it enters the passenger compartment. This makes the cabin noticeably quieter and creates a more peaceful driving experience. It's a comfort feature, not a safety one; standard laminated windscreens already meet impact safety requirements.
Check your windscreen for an ear symbol, the word 'Acoustic', a capital 'A', or the term 'SoundScreen' printed in one of the four corners. These markings indicate acoustic-grade glass. You can also ask your vehicle's dealership or service centre whether your model came fitted with acoustic glass—it's often a factory option on comfort or premium trims.
Acoustic glass is always laminated and bonds to the frame like any standard windscreen, so replacement follows the normal bonded-glass procedure. No specialist calibration is required. The replacement technician will fit it using standard adhesive and sealant. Cure time and drive-away restrictions are identical to standard laminated windscreens. Acoustic glass is widely available as an aftermarket OE-equivalent option.
A camera mounted near the rear-view mirror monitors the road ahead for lane-keep and traffic-sign features.
A forward-facing camera positioned in the windscreen header area (typically mounted on or near the rear-view mirror bracket) captures video of the road ahead. This camera feeds data to driver-assistance systems such as lane-departure warning, lane-keep assist, autonomous emergency braking, and traffic-sign recognition. The camera is a core component of modern ADAS (Advanced Driver Assistance Systems) and requires precise alignment after windscreen replacement to ensure these safety features function correctly.
Look for a small dark triangular or lens-shaped component mounted in the black plastic trim area above the windscreen, typically centred near the rear-view mirror or slightly to one side. Your vehicle's handbook or infotainment menu may reference 'Lane Assist', 'Traffic Sign Recognition', or 'Autonomous Emergency Braking'. Ask your dealer or service centre directly if your car is equipped with a forward-facing camera system.
Windscreen replacement on camera-equipped vehicles requires calibration of the camera system after the new glass is fitted. The exact calibration procedure—whether static (using a target board in a controlled environment) or dynamic (road-based)—varies by vehicle make, model, and year. We confirm the precise calibration requirement when we look up your specific vehicle. Calibration ensures lane-keep, sign recognition, and emergency-braking systems function safely. This may extend the fitting schedule and may necessitate workshop-based fitting rather than mobile attendance.
We confirm the exact procedure for your specific vehicle when you book.
The moulded trim that surrounds your camera and sensor cluster at the top of the windscreen, typically transferred or supplied with replacement glass.
A bracket for safety features is the moulded plastic or composite shroud that sits at the top of the windscreen, framing and protecting the camera and sensor cluster mounted behind the rear-view mirror. This trim cover houses forward-facing driver-assistance cameras and sensors — equipment that monitors the road ahead for lane-keeping, collision warning, adaptive cruise control, and similar safety functions. The bracket itself is part of the vehicle's structural frame, but the trim cover you see is what protects and aesthetically integrates the technology into the windscreen area.
Look at the top centre of your windscreen, just above or around the rear-view mirror. If you see a dark moulded shroud or trim panel — often rectangular or tapered — with a visible lens or sensor window, your vehicle has a bracket for safety features. Your service history or handbook will list any ADAS (Advanced Driver Assistance System) technologies fitted. Ask your dealer or service centre if your vehicle has forward-facing cameras or sensors; if it does, you have a bracket for safety features.
On windscreen replacement, the trim cover is typically transferred from your old glass to the new one, or supplied pre-integrated with the replacement depending on the variant. This means minimal disruption to your safety system during the swap. However, if the bracket requires recalibration after glass replacement — which depends on your specific vehicle and camera type — the job may require static calibration (using a target board) or dynamic calibration (a road drive). We confirm the exact calibration procedure when we look up your vehicle.
We confirm the exact procedure for your specific vehicle when you book.
Dynamic calibration uses road driving to recalibrate your camera after windscreen replacement.
Dynamic camera calibration is a procedure in which a technician drives the vehicle on marked roads at set speeds after the windscreen has been fitted and the adhesive has cured. During this drive, the forward-facing camera relearns its reference points — lane markings, road signs, road edges and surrounding traffic patterns — so it can resume accurate operation of camera-dependent safety and driver-assistance systems. This recalibration is necessary because any windscreen replacement, even with precision fitting, can introduce small shifts in the camera's optical alignment relative to the road.
Check your vehicle's handbook or contact your dealer to confirm whether your car has a forward-facing camera system. If it does, ask the dealer whether your specific model requires dynamic (road-drive) or static (target-board) calibration after windscreen replacement. You can also ask your fitter — they will establish this when they look up your vehicle's specification.
After your windscreen is fitted and the bonding has cured, a technician will drive the vehicle on marked roads at controlled speeds to allow the camera to relearn its environment. This extends the overall job duration beyond the glass-fitting time alone. Depending on your vehicle, calibration may be performed during the same visit or scheduled separately. We confirm the exact procedure and location (mobile or workshop) when we look up your specific vehicle.
We confirm the exact procedure for your specific vehicle when you book.
GPS antenna built into the windscreen connects your sat-nav to satellite signals for reliable navigation.
A GPS antenna is laminated into the windscreen glass during manufacture, providing a direct aerial connection for your vehicle's satellite-navigation system. This integrated design offers better signal reception than external antennas and a cleaner aesthetic. The antenna print and electrical connector are engineered into the glass itself, allowing the navigation receiver to lock onto GPS satellites without interference from the vehicle's metal body or other components.
Check your vehicle's handbook or ask your dealership service centre whether your windscreen carries an integrated GPS antenna. You won't see obvious external aerials or connectors on the glass itself — the antenna is laminated internally. If your sat-nav works reliably without a visible roof-mounted antenna, it's likely GPS-equipped.
Replacement windscreens with GPS antennas must be sourced as OEM (original-equipment) glass to preserve navigation functionality. The antenna print pattern and electrical connector are specific to your vehicle's sat-nav system. Aftermarket glass without the antenna print will not support GPS reception. We confirm OEM availability when you book; lead times may be slightly longer than standard glass.
Heat-absorbing PVB interlayer reduces solar gain and cabin temperature on warm days—but must match your original spec.
Heat-absorbing PVB is a specially formulated interlayer sandwiched between the glass plies in your windscreen. It absorbs a portion of the sun's infrared radiation before it enters the cabin, reducing solar heat gain on warm days. This keeps the interior cooler and reduces air-conditioning workload. The feature is built into the glass during manufacture and cannot be added or removed after production. If your vehicle left the factory with this interlayer, any replacement windscreen must carry the same PVB specification to maintain the original thermal performance.
Check your vehicle's specification sheet or handbook—heat-absorbing PVB is listed under windscreen or glass specification. You can also ask your dealership service centre or provide us with your vehicle registration; we'll confirm whether your car came with this feature as standard or as an option.
Replacement windscreens with heat-absorbing PVB must be sourced to the exact OE specification—aftermarket alternatives with standard PVB will not deliver the same solar-control performance. We ensure the correct spec is ordered before the fit. No calibration is required. Installation and cure procedures are identical to standard windscreen replacement; the interlayer is integral to the glass and requires no additional treatment.
Heated windscreens use embedded wires to quickly clear ice and condensation in cold weather.
A heated windscreen is integrated with a fine mesh of electrical wires embedded within the glass itself. When activated, these wires generate heat to warm the windscreen surface, helping to rapidly clear frost, ice, and condensation during cold or damp conditions. This feature improves visibility and safety in winter driving and reduces reliance on engine heat and demister air, which can be slower on very cold mornings.
Check your vehicle's handbook or contact your dealership service centre — they can confirm whether your model includes this feature. Look for a dashboard symbol (usually a windscreen icon with heat waves) when you activate the function, or check your infotainment settings for a heating or climate option linked to the windscreen. Some vehicles have a dedicated button on the stalk or console.
Heated windscreens require replacement glass to be of the correct heated specification — standard unheated glass cannot be fitted. The replacement glass must be sourced to match your vehicle's exact heated-wire configuration. Installation is straightforward, though the technician will confirm the heating element is functioning correctly after fitting. No calibration is required for this feature.
A single camera mounted near the rear-view mirror that helps with lane-keeping and collision avoidance.
A mono camera is a single-lens camera positioned behind the windscreen, typically in the upper centre area near the rear-view mirror. It captures the road ahead and uses computer vision to detect lane markings, vehicles, and road hazards. The camera feeds data to driver-assistance systems such as lane-keeping assist, lane-departure warning, and forward-collision warning. It forms the visual foundation of these safety features, allowing the vehicle to monitor road position and surrounding traffic automatically.
Look in the black trim area above the windscreen, centred behind the rear-view mirror — you will see a small triangular lens assembly or dark lens cover. Check your vehicle handbook or ask your dealer's service department to confirm your model has lane-assistance or collision-warning features; vehicles with these systems almost always have a mono camera. Dashboard warning symbols related to lane or collision systems also indicate the presence of this camera.
When the windscreen is replaced, the camera bracket and lens assembly must be removed and carefully repositioned on the new glass. The camera may require calibration after fitting to ensure accurate road detection and lane recognition. Calibration needs vary by vehicle — we confirm the exact procedure when we look up your specific vehicle. The job may take longer than a standard windscreen replacement, and workshop facilities may be required if calibration demands a controlled environment.
We confirm the exact procedure for your specific vehicle when you book.
Heated zones around sensors prevent frost and moisture buildup, helping your safety systems work reliably.
A sensor heated zone is an electrical heating element integrated into or around camera, radar, or sensor mounts on the windscreen. Its purpose is to prevent frost, ice, condensation, and moisture accumulation on sensor lenses and housings. This keeps safety systems — such as lane-keeping assist, collision warning, and adaptive cruise control — functioning accurately in cold, wet, or foggy conditions. Without this heating, moisture or ice can obscure sensors and cause them to malfunction or deactivate.
Check your vehicle's handbook for mention of 'heated sensor zone' or 'sensor heating' in the windscreen or ADAS section. Look at the top edge of your windscreen where cameras or radar modules are mounted — you may see small heating elements or wiring near these components. Ask your dealership or service centre directly: they can confirm whether your specific model includes sensor heating as standard.
Windscreens with heated sensor zones require careful handling during replacement to preserve the heating element and its electrical connections. The heating circuit must be reconnected properly after the new glass is fitted. Depending on the vehicle, this may involve static or dynamic camera calibration after installation. We confirm the exact procedure — including any calibration needs — when we look up your vehicle details.
We confirm the exact procedure for your specific vehicle when you book.
A blue-tinted gradient band across the top of your windscreen that reduces glare without affecting your view of the road.
A blue sun strip is a tinted gradient band built into the upper edge of your windscreen's laminate layer. It reduces glare from sunlight reflecting off the road and bonnet without darkening your main field of vision. The tint is created during manufacture as part of the glass laminate itself — it cannot be added or removed later. Sun strips are a windscreen-only feature; rear and side windows cannot carry this effect because they use tempered rather than laminated glass.
Look at the top of your windscreen from inside the car — you'll see a distinct blue-tinted band running horizontally across the upper portion. Check your vehicle's specification sheet or ask your dealership service centre whether your windscreen is listed as a 'blue sun strip' or 'tinted sun strip' variant. Your invoice or parts manual will confirm it.
When replacing a windscreen with a blue sun strip, the replacement must be the sun-strip variant — a standard plain windscreen will not replicate the tinted band. Your replacement glass is sourced as an exact match to your original specification. There are no additional calibration or cure implications beyond a standard windscreen replacement. Fitting and drive-away times remain unchanged.
Clear windscreen glass has no tint; most cars have a slight tint as standard.
A clear windscreen contains no added tint layer. Most modern windscreens incorporate a subtle tint (typically blue, green, grey or bronze) as standard to reduce glare, provide UV protection, and improve cabin comfort. A genuinely clear windscreen is the absence of this tint. Clear glass is less common than tinted variants and is sometimes specified for aesthetic or operational reasons, though the tint difference is usually imperceptible to the naked eye.
Lower your side window halfway and hold a white piece of paper behind it. If you see a noticeable colour cast (blue, green, grey or bronze) in the side glass, your windscreen has the same tint. If the side glass appears colourless, your windscreen is likely clear. You can also ask your vehicle's dealership or service centre to confirm the windscreen specification in your service records.
Clear windscreen replacement uses the same installation process as any other windscreen. No special calibration or extended cure time applies. Sourcing is straightforward — clear glass is widely available as an aftermarket replacement. Installation time and drive-away restrictions follow standard windscreen replacement timings. If your vehicle has ADAS features (forward-facing camera or radar), calibration may be required after replacement depending on your specific vehicle; we confirm this when we look up your car details.
Coated windscreens have a blue or purple tint and protect your car from UV rays and heat.
A coated windscreen has a special protective layer applied to the glass that appears as a blue or purple tint and often reflects a silvery-blue colour in bright sunlight. This coating is designed to reduce the amount of ultraviolet (UV) radiation and solar heat that enters the vehicle, helping to keep the interior cooler and protecting upholstery and dashboard components from UV damage and fading. The coating is integral to the glass and doesn't require any special maintenance from you.
Look at your windscreen in bright daylight — a coated windscreen will show a distinct blue or purple tint and a silvery-blue reflection when the sun hits it directly. Check your vehicle's service booklet or window sticker (usually on the driver's door jamb), which may list the glass specification. Alternatively, ask your dealership or service centre to confirm whether your windscreen carries a UV or heat-rejection coating.
When replacing a coated windscreen, the replacement glass must match the original specification — including the coating type and tint level — to maintain the same UV and heat protection and to preserve the vehicle's interior aesthetics. Original-equipment or equivalent aftermarket coated glass is sourced to specification. The coating is applied during glass manufacture; no post-fit treatment is required. Fitting and cure times are unaffected by the presence of the coating.
A Head-Up Display projects your speed, navigation cues and key alerts onto the windscreen so you can read them without looking down.
A Head-Up Display (HUD) projects driving information — speed, navigation cues, ADAS alerts — onto the windscreen in your line of sight, so you can read it without taking your eyes off the road. The projector is mounted in the dashboard and shines the image upwards onto a special HUD-compatible windscreen that uses a wedge-shaped laminate to prevent a ghost image. The image typically appears to float a few feet ahead of the car. Common on premium and sports models, increasingly standard on mid-range cars from the 2020s onwards.
Check your vehicle's specification sheet or handbook under 'display features' or 'HUD'. Look for a small projector unit mounted on the dashboard, typically below the steering wheel or in the instrument cluster area. When you start the vehicle, a bright image should appear on the lower windscreen area. Your dealer's service centre can confirm whether your specific model and trim level includes a HUD.
Your replacement windscreen needs to be HUD-compatible — built with the correct wedge laminate so the projected image stays sharp and double-free. Once the HUD-compatible glass is fitted, the projector itself typically doesn't need recalibration: image position is user-adjustable via your dashboard controls. We confirm your vehicle uses the HUD-compatible windscreen variant when ordering, so the replacement matches the original.
The Volvo V60 has been in continuous production since 2010, evolving through multiple generations with significant windscreen technology advancement. Early models carry straightforward laminated windscreens with basic rain sensors, while mid-generation V60s (from around 2015 onwards) introduce green-tinted glass, acoustic interlayers, and integrated GPS antennas as standard or optional fitment across higher trims.
From the second generation (2018+), Volvo's IntelliSafe driver-assistance suite became increasingly common, bringing forward-facing mono cameras integrated into the windscreen frame and requiring calibration after replacement. Later variants often feature heated windscreens, sensor-heated zones to prevent frost affecting camera performance, and LIDAR systems for advanced collision avoidance — each requiring specialist knowledge at fit and calibration time.
Own a different Volvo? We've got you — every variant, every year.
The questions customers ask us most often.
