Nissan Juke windscreen replacement — booked online.

The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older Jukes can still be booked.

Curious why prices vary so widely? Read our UK windscreen replacement cost guide .

What to expect during your Nissan Juke windscreen replacement

Booking a Nissan Juke windscreen replacement takes just a few straightforward steps.

1. 1

   Complete a quick online quote using our guided widget — takes about a minute and identifies your exact variant.

2. 2

   Confirm your booking and select a fitting time that suits you.

3. 3

   Our parts team verifies your glass specification and confirms the fitter who will carry out the replacement.

4. 4

   On the day, your fitter arrives at your chosen location (typically mobile at your address), removes the damaged windscreen, and fits the replacement matched to your factory specification.

5. 5

   If your Juke is equipped with ProPILOT Assist, static camera calibration is completed at a workshop location after the glass is set — scheduled as part of the same booking.

6. 6

   Your fitter confirms the minimum drive-away time before leaving, and you're covered by a two-year warranty on the workmanship and glass quality.

The whole process is designed to be simple — our network of independent specialists handles the logistics so you don't have to.

What features does your Juke have?

Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.

• Green10

  2010–2026

  Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.

  What it means

  Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.

  How to tell

  The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.

  Replacement impact

  Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.

• Vin Notch10

  2010–2026

  A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.

  What it means

  A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.

  How to tell

  Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.

  Replacement impact

  When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.

• Right Hand Drive Part9

  2010–2026

  A glass variant made specifically for right-hand-drive vehicles like UK cars, with brackets and sensors positioned for the driver's side.

  What it means

  Right-hand-drive glass is a windscreen (or other glass panel) manufactured to the correct specification for vehicles where the steering wheel and driver controls are on the right side of the car. The key difference isn't the glass itself but the position of brackets, sensor mounting pads, and sometimes a VIN (Vehicle Identification Number) notch. These are placed on the dashboard side to align with right-hand-drive vehicle architecture. Using the correct variant ensures all safety systems, mounting points, and sensor arrays sit in the right place when the glass is fitted.

  How to tell

  Check your vehicle's specification sheet or service handbook — it will confirm 'RHD' (right-hand drive). Ask your dealership or service centre which windscreen variant they stock for your model. If you're unsure, provide us with your registration number when you book; we'll identify the correct part.

  Replacement impact

  UKCG stocks the UK-specific right-hand-drive variant, so all brackets, sensors, and mounting points align correctly during fitting. Using a left-hand-drive part on a right-hand-drive vehicle would result in misalignment of camera brackets, rain sensors, or other dashboard-mounted components. We confirm you receive the correct RHD variant before dispatch.

• Acoustic (Noise reduction)7

  2010–2026

  Acoustic glass reduces cabin noise for a quieter, more comfortable ride.

  What it means

  Acoustic windscreen glass is laminated with a special acoustic interlayer that absorbs and dampens sound vibrations. It reduces exterior noise—from traffic, wind, and road surface—before it enters the passenger compartment. This makes the cabin noticeably quieter and creates a more peaceful driving experience. It's a comfort feature, not a safety one; standard laminated windscreens already meet impact safety requirements.

  How to tell

  Check your windscreen for an ear symbol, the word 'Acoustic', a capital 'A', or the term 'SoundScreen' printed in one of the four corners. These markings indicate acoustic-grade glass. You can also ask your vehicle's dealership or service centre whether your model came fitted with acoustic glass—it's often a factory option on comfort or premium trims.

  Replacement impact

  Acoustic glass is always laminated and bonds to the frame like any standard windscreen, so replacement follows the normal bonded-glass procedure. No specialist calibration is required. The replacement technician will fit it using standard adhesive and sealant. Cure time and drive-away restrictions are identical to standard laminated windscreens. Acoustic glass is widely available as an aftermarket OE-equivalent option.

• Fitting Hardware5

  2010–2026

  Pre-fitted clips and brackets that secure the glass to your vehicle, supplied ready to bond as a complete unit.

  What it means

  Fitting hardware comprises the clips, brackets, mouldings and adhesive retention components that hold the glass securely in place on your vehicle's frame. When your replacement glass is supplied with fitting hardware pre-attached, it arrives as a ready-to-install assembly rather than as bare glass requiring separate hardware attachment during the fit. This streamlines the replacement process and ensures correct positioning and fitment.

  How to tell

  Check your vehicle's service history or contact your dealership service department with your registration number. They can confirm whether your glass comes with pre-fitted hardware as standard. Visually, pre-fitted hardware appears as clips or brackets already bonded or attached to the glass edges before it reaches the fitting technician.

  Replacement impact

  Glass supplied with pre-fitted hardware typically requires no additional labour to attach clips or brackets during the fit, reducing technician time at the vehicle. The hardware must be in good condition and correctly positioned for the glass to seal and function properly. If hardware is damaged during removal of the old glass, replacement or repair of that hardware may be needed before the new glass can be fitted securely.

• Rain Sensor5

  2010–2026No calibration after replacement

  Your wipers automatically activate when rain falls on the windscreen.

  What it means

  A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.

  How to tell

  Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.

  Replacement impact

  Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.

• Solar Control4

  2010–2019

  Solar control glass absorbs infrared rays to reduce heat and improve cabin comfort.

  What it means

  Solar control is a coating applied to the windscreen that absorbs the sun's infrared radiation rather than allowing it to pass through into the cabin. This reduces solar heat gain, helping to keep the interior cooler and more comfortable, particularly in warm weather or direct sunlight. The coating is transparent to visible light, so it doesn't darken the windscreen or affect visibility. It's a passive thermal management feature that works continuously whenever the sun is shining on the glass.

  How to tell

  Check your vehicle's specification sheet or contact your dealership service centre to confirm whether solar control glass is fitted. Some manufacturers list it as 'solar control windscreen', 'heat-reflective glass', or 'thermal management glass'. It's a factory-fitted feature and won't be visibly obvious from outside the car — the coating is integral to the glass itself.

  Replacement impact

  Solar control glass is a factory-fitted specification. When replacing the windscreen, a solar control variant must be sourced to match the original. This is a standard glass type with no special fitting implications or calibration requirements. Cure and drive-away times follow normal windscreen bonding procedures. Confirm with your fitter that the replacement glass includes solar control to maintain the original thermal performance.

• Camera3

  2020–2026Calibration varies by vehicle

  A camera mounted near the rear-view mirror monitors the road ahead for lane-keep and traffic-sign features.

  What it means

  A forward-facing camera positioned in the windscreen header area (typically mounted on or near the rear-view mirror bracket) captures video of the road ahead. This camera feeds data to driver-assistance systems such as lane-departure warning, lane-keep assist, autonomous emergency braking, and traffic-sign recognition. The camera is a core component of modern ADAS (Advanced Driver Assistance Systems) and requires precise alignment after windscreen replacement to ensure these safety features function correctly.

  How to tell

  Look for a small dark triangular or lens-shaped component mounted in the black plastic trim area above the windscreen, typically centred near the rear-view mirror or slightly to one side. Your vehicle's handbook or infotainment menu may reference 'Lane Assist', 'Traffic Sign Recognition', or 'Autonomous Emergency Braking'. Ask your dealer or service centre directly if your car is equipped with a forward-facing camera system.

  Replacement impact

  Windscreen replacement on camera-equipped vehicles requires calibration of the camera system after the new glass is fitted. The exact calibration procedure—whether static (using a target board in a controlled environment) or dynamic (road-based)—varies by vehicle make, model, and year. We confirm the precise calibration requirement when we look up your specific vehicle. Calibration ensures lane-keep, sign recognition, and emergency-braking systems function safely. This may extend the fitting schedule and may necessitate workshop-based fitting rather than mobile attendance.

• Encapsulation3

  2020–2026

  Factory-bonded rubber or polymer trim means your replacement glass arrives ready to fit as one complete unit.

  What it means

  Encapsulation is a rubber or polymer gasket moulded directly onto the glass edges during manufacturing. The trim is bonded to the glass at the factory — either by injection moulding, PU robot extrusion, or adhesive bonding. When you need a replacement, the entire panel arrives with its trim already attached, so the glass and gasket are replaced together as a single unit rather than as separate components.

  How to tell

  Check your current windscreen or rear window edges. If you see a continuous rubber or polymer seal running around the perimeter that appears moulded or permanently bonded to the glass itself — rather than a separate trim clipped or screwed to the frame — your glass is encapsulated. Ask your dealer or service centre to confirm; they can also check your vehicle specification sheet.

  Replacement impact

  Encapsulated glass simplifies replacement because there's no separate trim to remove, refit, or source. The bonded gasket is replaced as part of the glass unit, which reduces installation complexity and potential leak points. Cure time and drive-away procedures remain unchanged. No additional sourcing delays — encapsulated replacements are stocked as complete assemblies by most suppliers.

• Heated Windscreen2

  2020–2026

  Heated windscreens use embedded wires to quickly clear ice and condensation in cold weather.

  What it means

  A heated windscreen is integrated with a fine mesh of electrical wires embedded within the glass itself. When activated, these wires generate heat to warm the windscreen surface, helping to rapidly clear frost, ice, and condensation during cold or damp conditions. This feature improves visibility and safety in winter driving and reduces reliance on engine heat and demister air, which can be slower on very cold mornings.

  How to tell

  Check your vehicle's handbook or contact your dealership service centre — they can confirm whether your model includes this feature. Look for a dashboard symbol (usually a windscreen icon with heat waves) when you activate the function, or check your infotainment settings for a heating or climate option linked to the windscreen. Some vehicles have a dedicated button on the stalk or console.

  Replacement impact

  Heated windscreens require replacement glass to be of the correct heated specification — standard unheated glass cannot be fitted. The replacement glass must be sourced to match your vehicle's exact heated-wire configuration. Installation is straightforward, though the technician will confirm the heating element is functioning correctly after fitting. No calibration is required for this feature.

• Other Hardware2

  2020–2026

  Factory-fitted brackets and mounts bonded to the glass, pre-assembled and ready to fit without sub-assembly.

  What it means

  Other Hardware refers to factory-fitted brackets, mounts, connectors, or trim pieces bonded permanently to the windscreen or other glass during manufacturing. These are integral to the vehicle's design but do not activate or control a specific feature — they simply secure or position components like sensors, trim strips, or mounting points. Unlike feature-specific hardware, these items are passive structural elements. A replacement carrying Other Hardware arrives pre-bonded and ready to install without additional assembly or modification.

  How to tell

  Check your vehicle documentation or ask your dealership service centre whether your windscreen or glass panel carries factory-bonded brackets or mounts. Visual inspection may reveal trim strips, sensor housings, or antenna mounts bonded to the edges or interior surface of the glass. Your original invoice or parts list will specify if Other Hardware is present.

  Replacement impact

  Replacement glass carrying Other Hardware must be sourced as a complete assembly — the brackets and mounts come pre-bonded from the supplier and cannot be transferred from the old glass. Installation is straightforward: the fitter removes the old glass and fits the replacement with its hardware already in place. No additional sub-assembly, bonding, or recalibration of the hardware itself is required. Fitting time is unaffected.

• Mono Camera1

  2020–2026Calibration varies by vehicle

  A single camera mounted near the rear-view mirror that helps with lane-keeping and collision avoidance.

  What it means

  A mono camera is a single-lens camera positioned behind the windscreen, typically in the upper centre area near the rear-view mirror. It captures the road ahead and uses computer vision to detect lane markings, vehicles, and road hazards. The camera feeds data to driver-assistance systems such as lane-keeping assist, lane-departure warning, and forward-collision warning. It forms the visual foundation of these safety features, allowing the vehicle to monitor road position and surrounding traffic automatically.

  How to tell

  Look in the black trim area above the windscreen, centred behind the rear-view mirror — you will see a small triangular lens assembly or dark lens cover. Check your vehicle handbook or ask your dealer's service department to confirm your model has lane-assistance or collision-warning features; vehicles with these systems almost always have a mono camera. Dashboard warning symbols related to lane or collision systems also indicate the presence of this camera.

  Replacement impact

  When the windscreen is replaced, the camera bracket and lens assembly must be removed and carefully repositioned on the new glass. The camera may require calibration after fitting to ensure accurate road detection and lane recognition. Calibration needs vary by vehicle — we confirm the exact procedure when we look up your specific vehicle. The job may take longer than a standard windscreen replacement, and workshop facilities may be required if calibration demands a controlled environment.

  Calibration mix across our Nissan variants

  • 1Static

  We confirm the exact procedure for your specific vehicle when you book.

• Nissan Kubistar From £249
• Nissan Interstar From £252
• Nissan Almera From £256
• Nissan Micra From £285
• Nissan NV200 From £288
• Nissan Primastar From £288
• Nissan Note From £289
• Nissan Primera From £297
• Nissan Navara From £304
• Nissan Pathfinder From £304
• Nissan Pixo From £305
• Nissan Patrol From £309