Instant quote across six Kia Stonic variants from 2017 onwards, fitted by approved fitters — booked in under two minutes.
Make
Kia
Model
Stonic
No card required · Free to quote
Prices vary based on the presence of ADAS camera systems and calibration requirements. Earlier Stonics without DriveWise cameras are typically more affordable to replace. Later models equipped with forward-facing cameras and static calibration demands incur higher costs owing to the additional technical work required after the glass is fitted.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2026 | £708 — £708 | 1 variant | Price my 2026 |
| 2025 | £708 — £708 | 1 variant | Price my 2025 |
| 2024 | £708 — £708 | 1 variant | Price my 2024 |
| 2023 | £398 — £708 | 6 variants | Price my 2023 |
| 2022 | £398 — £708 | 6 variants | Price my 2022 |
| 2021 | £398 — £708 | 6 variants | Price my 2021 |
| 2020 | £398 — £708 | 6 variants | Price my 2020 |
| 2019 | £398 — £708 | 6 variants | Price my 2019 |
| 2018 | £398 — £708 | 6 variants | Price my 2018 |
| 2017 | £398 — £708 | 6 variants | Price my 2017 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older Stonics can still be booked.
Curious why prices vary so widely? Read our UK windscreen replacement cost guide .
Reviews below are hand-picked from recent UK customers. Across the whole of UK Car Glass, 4.82/5 from 1,422 Trustpilot reviews.
Booking a replacement for your Stonic windscreen is straightforward and takes just a few minutes online.
Complete a quick quiz on our website to identify your exact variant — we'll confirm the right glass for your model year and trim.
Receive an instant quote and choose your preferred date and time.
We'll match you with a local approved fitter who sources the correct glass and handles any calibration work.
Your fitter will either visit you at home (if no calibration is needed) or invite you to their workshop (if ADAS calibration is required post-fit).
The replacement typically takes an hour or so, after which your fitter will confirm the drive-away time.
You're covered by a two-year warranty on both the glass and the workmanship.
Once booked, you'll have full support from our team until the job is complete and your Stonic is back on the road safely.
Most Stonics with ADAS cameras require static calibration after windscreen replacement, which must be done at a workshop using printed target boards and diagnostic equipment. If your Stonic carries a DriveWise camera, your fitter will schedule the entire job — replacement and calibration — at their workshop to ensure the process is completed safely and accurately.
Mobile fitting at your home is available for camera-free variants, or by prior arrangement if calibration isn't required. Either way, your fitter will confirm the location and timing when you book.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.
Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.
The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.
Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
A camera mounted near the rear-view mirror monitors the road ahead for lane-keep and traffic-sign features.
A forward-facing camera positioned in the windscreen header area (typically mounted on or near the rear-view mirror bracket) captures video of the road ahead. This camera feeds data to driver-assistance systems such as lane-departure warning, lane-keep assist, autonomous emergency braking, and traffic-sign recognition. The camera is a core component of modern ADAS (Advanced Driver Assistance Systems) and requires precise alignment after windscreen replacement to ensure these safety features function correctly.
Look for a small dark triangular or lens-shaped component mounted in the black plastic trim area above the windscreen, typically centred near the rear-view mirror or slightly to one side. Your vehicle's handbook or infotainment menu may reference 'Lane Assist', 'Traffic Sign Recognition', or 'Autonomous Emergency Braking'. Ask your dealer or service centre directly if your car is equipped with a forward-facing camera system.
Windscreen replacement on camera-equipped vehicles requires calibration of the camera system after the new glass is fitted. The exact calibration procedure—whether static (using a target board in a controlled environment) or dynamic (road-based)—varies by vehicle make, model, and year. We confirm the precise calibration requirement when we look up your specific vehicle. Calibration ensures lane-keep, sign recognition, and emergency-braking systems function safely. This may extend the fitting schedule and may necessitate workshop-based fitting rather than mobile attendance.
The moulded trim that surrounds your camera and sensor cluster at the top of the windscreen, typically transferred or supplied with replacement glass.
A bracket for safety features is the moulded plastic or composite shroud that sits at the top of the windscreen, framing and protecting the camera and sensor cluster mounted behind the rear-view mirror. This trim cover houses forward-facing driver-assistance cameras and sensors — equipment that monitors the road ahead for lane-keeping, collision warning, adaptive cruise control, and similar safety functions. The bracket itself is part of the vehicle's structural frame, but the trim cover you see is what protects and aesthetically integrates the technology into the windscreen area.
Look at the top centre of your windscreen, just above or around the rear-view mirror. If you see a dark moulded shroud or trim panel — often rectangular or tapered — with a visible lens or sensor window, your vehicle has a bracket for safety features. Your service history or handbook will list any ADAS (Advanced Driver Assistance System) technologies fitted. Ask your dealer or service centre if your vehicle has forward-facing cameras or sensors; if it does, you have a bracket for safety features.
On windscreen replacement, the trim cover is typically transferred from your old glass to the new one, or supplied pre-integrated with the replacement depending on the variant. This means minimal disruption to your safety system during the swap. However, if the bracket requires recalibration after glass replacement — which depends on your specific vehicle and camera type — the job may require static calibration (using a target board) or dynamic calibration (a road drive). We confirm the exact calibration procedure when we look up your vehicle.
Factory-fitted brackets and mounts bonded to the glass, pre-assembled and ready to fit without sub-assembly.
Other Hardware refers to factory-fitted brackets, mounts, connectors, or trim pieces bonded permanently to the windscreen or other glass during manufacturing. These are integral to the vehicle's design but do not activate or control a specific feature — they simply secure or position components like sensors, trim strips, or mounting points. Unlike feature-specific hardware, these items are passive structural elements. A replacement carrying Other Hardware arrives pre-bonded and ready to install without additional assembly or modification.
Check your vehicle documentation or ask your dealership service centre whether your windscreen or glass panel carries factory-bonded brackets or mounts. Visual inspection may reveal trim strips, sensor housings, or antenna mounts bonded to the edges or interior surface of the glass. Your original invoice or parts list will specify if Other Hardware is present.
Replacement glass carrying Other Hardware must be sourced as a complete assembly — the brackets and mounts come pre-bonded from the supplier and cannot be transferred from the old glass. Installation is straightforward: the fitter removes the old glass and fits the replacement with its hardware already in place. No additional sub-assembly, bonding, or recalibration of the hardware itself is required. Fitting time is unaffected.
Static calibration uses printed targets indoors to align your forward-facing camera after windscreen replacement.
Static camera calibration is a procedure in which a forward-facing camera system is realigned using printed target boards positioned at manufacturer-specified distances and heights in front of the vehicle. The vehicle remains stationary indoors throughout. A diagnostic tool reads the camera's view of these targets and adjusts the camera's alignment to factory specification. This ensures the camera can accurately detect road features, lane markings, pedestrians, and other objects — critical for driver-assistance systems like lane-keeping, collision warning, and adaptive cruise control to function safely and reliably.
Check your vehicle's handbook or ask your dealer's service centre whether your car has a forward-facing camera system that requires calibration after windscreen replacement. Look for driver-assistance features like lane-keeping assist, autonomous emergency braking, or adaptive cruise control on the dashboard menu. If your vehicle manual mentions 'camera calibration' or 'static target calibration', static calibration is likely part of your windscreen replacement service.
When a windscreen with an integrated or bracket-mounted camera is replaced, the camera's alignment can shift. Static calibration realigns the camera using indoor target boards, which must be performed in a workshop environment where printed targets can be positioned and secured at precise distances. This procedure is conducted after the windscreen is fitted and bonded. The workshop booking accommodates the additional time required for calibration, and we apply the no-split policy — both replacement and calibration happen at the same location on the same visit.
Some vehicles need a different calibration approach after windscreen replacement depending on their specific system.
Alternative calibration procedure refers to a non-standard method used to recalibrate camera or sensor systems after windscreen replacement on certain vehicles. Rather than a single universal approach, some cars require a tailored calibration method that differs from the most common procedure. This ensures safety-critical systems like lane-keeping assist, collision warning, and adaptive cruise control function correctly after new glass is fitted. The exact procedure depends on the vehicle's make, model, year, and the specific technology installed.
Check your vehicle's handbook or contact your dealer or service centre to confirm whether your car uses a standard or alternative calibration procedure. You can also ask us when you book — we look up your vehicle's exact requirements and confirm the calibration approach needed.
An alternative calibration procedure may require additional specialist equipment or a specific workshop setup that differs from standard calibration. Depending on the procedure, the job may take longer than a typical windscreen replacement, and we confirm the exact timescale and location (mobile or workshop) once we've identified your vehicle's requirements. In some cases, workshop attendance is necessary to access the required calibration tools or controlled environment.
A defogging detector automatically clears condensation from your windscreen, improving visibility in damp conditions.
A defogging detector is a sensor that monitors moisture levels on the windscreen and triggers the demister system automatically when condensation builds up. It improves driver visibility and safety in damp or cold weather by preventing manual intervention. The sensor typically sits near the rear-view mirror, positioned to sense moisture accumulation on the glass surface.
Check your vehicle's handbook or ask your dealer's service centre whether your model includes an automatic defogging or moisture-sensing demister. Look near the rear-view mirror for a small sensor unit. Some vehicles display an indicator light or message on the dashboard when the system is active.
The defogging detector does not affect windscreen replacement or require recalibration after fitting. The sensor itself remains in place and continues to function once the new windscreen is installed. No additional calibration, cure time, or specialist procedures are needed.
A single camera mounted near the rear-view mirror that helps with lane-keeping and collision avoidance.
A mono camera is a single-lens camera positioned behind the windscreen, typically in the upper centre area near the rear-view mirror. It captures the road ahead and uses computer vision to detect lane markings, vehicles, and road hazards. The camera feeds data to driver-assistance systems such as lane-keeping assist, lane-departure warning, and forward-collision warning. It forms the visual foundation of these safety features, allowing the vehicle to monitor road position and surrounding traffic automatically.
Look in the black trim area above the windscreen, centred behind the rear-view mirror — you will see a small triangular lens assembly or dark lens cover. Check your vehicle handbook or ask your dealer's service department to confirm your model has lane-assistance or collision-warning features; vehicles with these systems almost always have a mono camera. Dashboard warning symbols related to lane or collision systems also indicate the presence of this camera.
When the windscreen is replaced, the camera bracket and lens assembly must be removed and carefully repositioned on the new glass. The camera may require calibration after fitting to ensure accurate road detection and lane recognition. Calibration needs vary by vehicle — we confirm the exact procedure when we look up your specific vehicle. The job may take longer than a standard windscreen replacement, and workshop facilities may be required if calibration demands a controlled environment.
Your wipers automatically activate when rain falls on the windscreen.
A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.
Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.
Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.
A blue-tinted gradient band across the top of your windscreen that reduces glare without affecting your view of the road.
A blue sun strip is a tinted gradient band built into the upper edge of your windscreen's laminate layer. It reduces glare from sunlight reflecting off the road and bonnet without darkening your main field of vision. The tint is created during manufacture as part of the glass laminate itself — it cannot be added or removed later. Sun strips are a windscreen-only feature; rear and side windows cannot carry this effect because they use tempered rather than laminated glass.
Look at the top of your windscreen from inside the car — you'll see a distinct blue-tinted band running horizontally across the upper portion. Check your vehicle's specification sheet or ask your dealership service centre whether your windscreen is listed as a 'blue sun strip' or 'tinted sun strip' variant. Your invoice or parts manual will confirm it.
When replacing a windscreen with a blue sun strip, the replacement must be the sun-strip variant — a standard plain windscreen will not replicate the tinted band. Your replacement glass is sourced as an exact match to your original specification. There are no additional calibration or cure implications beyond a standard windscreen replacement. Fitting and drive-away times remain unchanged.
A glass variant made specifically for right-hand-drive vehicles like UK cars, with brackets and sensors positioned for the driver's side.
Right-hand-drive glass is a windscreen (or other glass panel) manufactured to the correct specification for vehicles where the steering wheel and driver controls are on the right side of the car. The key difference isn't the glass itself but the position of brackets, sensor mounting pads, and sometimes a VIN (Vehicle Identification Number) notch. These are placed on the dashboard side to align with right-hand-drive vehicle architecture. Using the correct variant ensures all safety systems, mounting points, and sensor arrays sit in the right place when the glass is fitted.
Check your vehicle's specification sheet or service handbook — it will confirm 'RHD' (right-hand drive). Ask your dealership or service centre which windscreen variant they stock for your model. If you're unsure, provide us with your registration number when you book; we'll identify the correct part.
UKCG stocks the UK-specific right-hand-drive variant, so all brackets, sensors, and mounting points align correctly during fitting. Using a left-hand-drive part on a right-hand-drive vehicle would result in misalignment of camera brackets, rain sensors, or other dashboard-mounted components. We confirm you receive the correct RHD variant before dispatch.
Solar control glass absorbs infrared rays to reduce heat and improve cabin comfort.
Solar control is a coating applied to the windscreen that absorbs the sun's infrared radiation rather than allowing it to pass through into the cabin. This reduces solar heat gain, helping to keep the interior cooler and more comfortable, particularly in warm weather or direct sunlight. The coating is transparent to visible light, so it doesn't darken the windscreen or affect visibility. It's a passive thermal management feature that works continuously whenever the sun is shining on the glass.
Check your vehicle's specification sheet or contact your dealership service centre to confirm whether solar control glass is fitted. Some manufacturers list it as 'solar control windscreen', 'heat-reflective glass', or 'thermal management glass'. It's a factory-fitted feature and won't be visibly obvious from outside the car — the coating is integral to the glass itself.
Solar control glass is a factory-fitted specification. When replacing the windscreen, a solar control variant must be sourced to match the original. This is a standard glass type with no special fitting implications or calibration requirements. Cure and drive-away times follow normal windscreen bonding procedures. Confirm with your fitter that the replacement glass includes solar control to maintain the original thermal performance.
The Kia Stonic is a compact crossover that launched in 2017, offering practicality and affordability across its range. All Stonic windscreens feature a green tint and a VIN notch for identification, with most carrying the visual hallmarks of modern safety systems.
From around the mid-2020s variant era, Kia began integrating its DriveWise ADAS suite into the Stonic, introducing forward-facing windscreen cameras for lane departure warning and collision-avoidance functions. Most modern Stonics now carry these camera systems, which require static calibration after glass replacement to ensure safe operation.
Replacement glass matches your original specification, and specialists on our network handle any calibration needed on the day — typically completed at a workshop to ensure accuracy.
Own a different Kia? We've got you — every variant, every year.
The questions customers ask us most often.
