Jaguar XF rear window replacement — booked online.

What to expect during your Jaguar XF rear window replacement

Replacing your rear window is straightforward, though the shattered glass means careful cleanup is part of the job.

1. 1

   You'll answer a short quiz to identify your exact variant — generation, trim, and specification features like heating and antenna circuits.

2. 2

   Once confirmed, our parts team checks that the correct rear window is in stock and ready.

3. 3

   You're matched with a local technician who can fit your specific variant and manages any integration with your vehicle's antenna or demisting systems.

4. 4

   On the day of fitting, the technician removes the damaged glass — which arrives in fragments — and carefully clears accessible shards before bonding the new panel.

5. 5

   You'll be given a minimum drive-away time, typically confirmed before the technician leaves.

6. 6

   For a thorough interior clean after fitting, we recommend a professional valet afterwards — glass shards can work into places that aren't easily reached on the day.

Your replacement comes with a two-year warranty covering workmanship and glass quality.

What features does your XF have?

Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.

• Encapsulation3

  2008–2024

  Factory-bonded rubber or polymer trim means your replacement glass arrives ready to fit as one complete unit.

  What it means

  Encapsulation is a rubber or polymer gasket moulded directly onto the glass edges during manufacturing. The trim is bonded to the glass at the factory — either by injection moulding, PU robot extrusion, or adhesive bonding. When you need a replacement, the entire panel arrives with its trim already attached, so the glass and gasket are replaced together as a single unit rather than as separate components.

  How to tell

  Check your current windscreen or rear window edges. If you see a continuous rubber or polymer seal running around the perimeter that appears moulded or permanently bonded to the glass itself — rather than a separate trim clipped or screwed to the frame — your glass is encapsulated. Ask your dealer or service centre to confirm; they can also check your vehicle specification sheet.

  Replacement impact

  Encapsulated glass simplifies replacement because there's no separate trim to remove, refit, or source. The bonded gasket is replaced as part of the glass unit, which reduces installation complexity and potential leak points. Cure time and drive-away procedures remain unchanged. No additional sourcing delays — encapsulated replacements are stocked as complete assemblies by most suppliers.

• Green3

  2008–2024

  Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.

  What it means

  Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.

  How to tell

  The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.

  Replacement impact

  Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.

• Solar Control3

  2008–2024

  Solar control glass absorbs infrared rays to reduce heat and improve cabin comfort.

  What it means

  Solar control is a coating applied to the windscreen that absorbs the sun's infrared radiation rather than allowing it to pass through into the cabin. This reduces solar heat gain, helping to keep the interior cooler and more comfortable, particularly in warm weather or direct sunlight. The coating is transparent to visible light, so it doesn't darken the windscreen or affect visibility. It's a passive thermal management feature that works continuously whenever the sun is shining on the glass.

  How to tell

  Check your vehicle's specification sheet or contact your dealership service centre to confirm whether solar control glass is fitted. Some manufacturers list it as 'solar control windscreen', 'heat-reflective glass', or 'thermal management glass'. It's a factory-fitted feature and won't be visibly obvious from outside the car — the coating is integral to the glass itself.

  Replacement impact

  Solar control glass is a factory-fitted specification. When replacing the windscreen, a solar control variant must be sourced to match the original. This is a standard glass type with no special fitting implications or calibration requirements. Cure and drive-away times follow normal windscreen bonding procedures. Confirm with your fitter that the replacement glass includes solar control to maintain the original thermal performance.

• Antenna2

  2008–2024

  An aerial laminated into the windscreen or rear window restores radio, DAB or TV reception without a roof-mounted mast.

  What it means

  An antenna is a conductive print laminated into the glass during manufacture, typically used for radio, DAB (digital audio broadcasting) or television reception. It replaces the traditional roof-mounted aerial mast found on older vehicles. The antenna is integrated into the glass interlayer and connected to the vehicle's receiver unit via a connector embedded in the glass edge. This design offers a cleaner aesthetic, reduces wind noise, and eliminates the vulnerability of a protruding mast to damage or theft.

  How to tell

  Check your vehicle's roof — if there is no visible aerial mast, your car likely has a laminated antenna. You can also ask your dealer or service centre whether your windscreen or rear window carries an antenna print. The connector may be visible on the glass edge or inside the door frame trim.

  Replacement impact

  When replacing glass with a laminated antenna, the replacement must carry the matching antenna print and connector to restore reception immediately on fitting. Aftermarket or original-equipment glass with the correct antenna specification is essential; a plain replacement will leave you without radio or DAB signal. Our fitters verify the antenna specification during booking and source the correct variant before the appointment.

• TV Antenna2

  2008–2024

  A TV-reception aerial printed into the rear window, typically for in-car entertainment systems.

  What it means

  A TV antenna is an aerial pattern laminated into the rear windscreen or rear side window to receive broadcast television signals. It's a separate system from the vehicle's radio or mobile antenna and is typically found in vehicles equipped with rear-seat entertainment systems. The antenna is printed directly onto or into the glass during manufacture, so when the glass is replaced, the antenna pattern must be reproduced on the replacement to maintain reception quality.

  How to tell

  Check your vehicle's specification sheet or handbook for rear-seat entertainment or TV tuner capability. If your car has a rear-seat entertainment system with a TV tuner, the rear window will have a TV antenna. You can also ask your dealer or service centre to confirm whether your vehicle has this feature.

  Replacement impact

  When the rear window is replaced, the replacement glass must include the matching TV antenna print to preserve reception. OEM (original equipment manufacturer) glass is typically required to ensure the antenna pattern is identical. The antenna is passive and requires no calibration or specialist procedures after fitting. Cure time for bonded rear glass is required; the fitter will confirm the drive-away time on the day.

• Alarm Wire1

  2015–2024

  A thin metal wire embedded in the glass forms part of your vehicle's alarm circuit and must be present in the replacement panel.

  What it means

  An alarm wire is a fine metal thread laminated into the windscreen or rear window glass as part of the vehicle's anti-theft or alarm system. Unlike heated-wire windscreens (which warm the glass), alarm wires carry a continuous electrical loop that detects glass breakage. When the glass shatters, the wire breaks and triggers the alarm. The wire serves no structural or visibility purpose—it exists purely for security detection.

  How to tell

  Check your vehicle handbook or ask your dealership service department whether your model includes an alarm wire in the windscreen or rear window. You won't see it easily from inside or outside the vehicle—it's laminated into the glass itself. If your car has an audible or visual alarm triggered by glass breakage (separate from motion sensors), an alarm wire is likely present.

  Replacement impact

  If your windscreen or rear window includes an alarm wire, the replacement glass must have an identical wire fitted to restore the alarm loop. This is a dealership-specification requirement and affects glass sourcing—aftermarket glass may not carry the wire, so OEM (original equipment) glass is often necessary. The wire itself does not affect fitting time, cure time, or calibration requirements. Confirm wire presence when booking so we source the correct glass variant.

• Silkscreen Modification1

  2015–2024

  A modified black-printed area around the rear-view mirror to suit your vehicle's camera or sensor layout.

  What it means

  Silkscreen modification refers to a variation in the black-printed area (called the 'frit') that surrounds the rear-view mirror on your windscreen. This printed zone is shaped to accommodate your vehicle's specific camera, sensor, or ADAS equipment layout. Different vehicles — even within the same model range — may have different camera positions or sensor configurations, requiring a bespoke print pattern. A silkscreen-modified windscreen is a distinct part with its own part number and cannot be used interchangeably with the standard print variant.

  How to tell

  Check your windscreen documentation or the original part number — dealership service records will confirm whether your windscreen carries a modified silkscreen. You can also ask your dealer's parts department to confirm the exact print variant for your vehicle's year and specification. The modification itself is visible as the black-printed border around the mirror area, but identifying whether it's 'modified' requires checking the part number rather than visual inspection alone.

  Replacement impact

  When your windscreen requires replacement, we must source the correct silkscreen variant for your specific vehicle to ensure proper camera and sensor clearance. Using an incorrect print variant could obstruct camera fields of view or interfere with sensor operation, compromising ADAS functionality and safety. We confirm the exact part number during the booking process to guarantee the correct glass is supplied and fitted. No additional calibration is triggered by the silkscreen modification itself; any calibration needed relates to the camera or sensor system, not the print.

• Jaguar XJ12 From £426
• Jaguar X-Type From £468
• Jaguar XK1 From £536
• Jaguar S-Type From £563
• Jaguar F-Pace From £792
• Jaguar XE From £860
• Jaguar XJ From £929