Instant quote across 14 Range Rover L405 variants in under 60 seconds, fitted by approved fitters — booked in under two minutes.
Make
Land Rover
Model
L405
No card required · Free to quote
Price variation across L405 variants is driven primarily by generation and ADAS capability. Older models without camera systems are the most affordable to replace. Newer L405s with InControl camera-based safety features incur additional calibration costs, and variants with heated or solar-control glass add to the replacement expense.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2026 | £597 — £1,587 | 11 variants | Price my 2026 |
| 2025 | £597 — £1,587 | 11 variants | Price my 2025 |
| 2024 | £597 — £1,587 | 11 variants | Price my 2024 |
| 2023 | £597 — £1,587 | 11 variants | Price my 2023 |
| 2022 | £597 — £1,587 | 11 variants | Price my 2022 |
| 2021 | £597 — £1,587 | 11 variants | Price my 2021 |
| 2020 | £597 — £1,587 | 11 variants | Price my 2020 |
| 2019 | £597 — £1,587 | 11 variants | Price my 2019 |
| 2018 | £597 — £1,587 | 11 variants | Price my 2018 |
| 2017 | £597 — £1,587 | 11 variants | Price my 2017 |
| 2016 | £597 — £1,587 | 10 variants | Price my 2016 |
| 2015 | £597 — £1,559 | 6 variants | Price my 2015 |
| 2014 | £597 — £921 | 4 variants | Price my 2014 |
| 2013 | £597 — £1,045 | 3 variants | Price my 2013 |
| 2012 | £836 — £1,045 | 2 variants | Price my 2012 |
| 2011 | £1,045 — £1,045 | 1 variant | Price my 2011 |
| 2010 | £1,045 — £1,045 | 1 variant | Price my 2010 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older L405s can still be booked.
Curious why prices vary so widely? Read our UK windscreen replacement cost guide .
Reviews below are hand-picked from recent UK customers. Across the whole of UK Car Glass, 4.82/5 from 1,422 Trustpilot reviews.
Booking your Range Rover L405 windscreen replacement online takes about two minutes — then a technician is matched to your variant and location.
1. Answer a short quiz on the quote page to confirm your model year and trim options — no registration needed.
2. Receive an instant quote and choose your preferred date and time.
3. Our network runs a parts check to confirm your exact glass spec, including any camera bracket or heated elements.
4. A technician in your area is matched to your booking and fitted glass is sourced.
5. Your fitter arrives and completes the replacement — typically 45–90 minutes for a windscreen, depending on your model. If ADAS calibration is required, the fitter completes it on the day.
6. Your windscreen is covered by a two-year warranty on workmanship and glass quality.
Drive-away time is confirmed by your fitter before they leave, and you're supported by our two-year warranty on the entire job.
Most L405 windscreen replacements can be fitted at your home or workplace by mobile technicians. However, if your L405 is equipped with InControl camera systems, the fitter will need a workshop environment with static calibration equipment to complete the job safely after the glass is set. This ensures your Lane Keep Assist and Forward Collision Warning functions are correctly aligned after replacement.
UKCG schedules the entire job — replacement and calibration — at the same workshop location to keep the process seamless and ensure you're never left without verified safety-critical calibration.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
Acoustic glass reduces cabin noise for a quieter, more comfortable ride.
Acoustic windscreen glass is laminated with a special acoustic interlayer that absorbs and dampens sound vibrations. It reduces exterior noise—from traffic, wind, and road surface—before it enters the passenger compartment. This makes the cabin noticeably quieter and creates a more peaceful driving experience. It's a comfort feature, not a safety one; standard laminated windscreens already meet impact safety requirements.
Check your windscreen for an ear symbol, the word 'Acoustic', a capital 'A', or the term 'SoundScreen' printed in one of the four corners. These markings indicate acoustic-grade glass. You can also ask your vehicle's dealership or service centre whether your model came fitted with acoustic glass—it's often a factory option on comfort or premium trims.
Acoustic glass is always laminated and bonds to the frame like any standard windscreen, so replacement follows the normal bonded-glass procedure. No specialist calibration is required. The replacement technician will fit it using standard adhesive and sealant. Cure time and drive-away restrictions are identical to standard laminated windscreens. Acoustic glass is widely available as an aftermarket OE-equivalent option.
Pre-fitted clips and brackets that secure the glass to your vehicle, supplied ready to bond as a complete unit.
Fitting hardware comprises the clips, brackets, mouldings and adhesive retention components that hold the glass securely in place on your vehicle's frame. When your replacement glass is supplied with fitting hardware pre-attached, it arrives as a ready-to-install assembly rather than as bare glass requiring separate hardware attachment during the fit. This streamlines the replacement process and ensures correct positioning and fitment.
Check your vehicle's service history or contact your dealership service department with your registration number. They can confirm whether your glass comes with pre-fitted hardware as standard. Visually, pre-fitted hardware appears as clips or brackets already bonded or attached to the glass edges before it reaches the fitting technician.
Glass supplied with pre-fitted hardware typically requires no additional labour to attach clips or brackets during the fit, reducing technician time at the vehicle. The hardware must be in good condition and correctly positioned for the glass to seal and function properly. If hardware is damaged during removal of the old glass, replacement or repair of that hardware may be needed before the new glass can be fitted securely.
Your wipers automatically activate when rain falls on the windscreen.
A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.
Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.
Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
Clear windscreen glass has no tint; most cars have a slight tint as standard.
A clear windscreen contains no added tint layer. Most modern windscreens incorporate a subtle tint (typically blue, green, grey or bronze) as standard to reduce glare, provide UV protection, and improve cabin comfort. A genuinely clear windscreen is the absence of this tint. Clear glass is less common than tinted variants and is sometimes specified for aesthetic or operational reasons, though the tint difference is usually imperceptible to the naked eye.
Lower your side window halfway and hold a white piece of paper behind it. If you see a noticeable colour cast (blue, green, grey or bronze) in the side glass, your windscreen has the same tint. If the side glass appears colourless, your windscreen is likely clear. You can also ask your vehicle's dealership or service centre to confirm the windscreen specification in your service records.
Clear windscreen replacement uses the same installation process as any other windscreen. No special calibration or extended cure time applies. Sourcing is straightforward — clear glass is widely available as an aftermarket replacement. Installation time and drive-away restrictions follow standard windscreen replacement timings. If your vehicle has ADAS features (forward-facing camera or radar), calibration may be required after replacement depending on your specific vehicle; we confirm this when we look up your car details.
Coated windscreens have a blue or purple tint and protect your car from UV rays and heat.
A coated windscreen has a special protective layer applied to the glass that appears as a blue or purple tint and often reflects a silvery-blue colour in bright sunlight. This coating is designed to reduce the amount of ultraviolet (UV) radiation and solar heat that enters the vehicle, helping to keep the interior cooler and protecting upholstery and dashboard components from UV damage and fading. The coating is integral to the glass and doesn't require any special maintenance from you.
Look at your windscreen in bright daylight — a coated windscreen will show a distinct blue or purple tint and a silvery-blue reflection when the sun hits it directly. Check your vehicle's service booklet or window sticker (usually on the driver's door jamb), which may list the glass specification. Alternatively, ask your dealership or service centre to confirm whether your windscreen carries a UV or heat-rejection coating.
When replacing a coated windscreen, the replacement glass must match the original specification — including the coating type and tint level — to maintain the same UV and heat protection and to preserve the vehicle's interior aesthetics. Original-equipment or equivalent aftermarket coated glass is sourced to specification. The coating is applied during glass manufacture; no post-fit treatment is required. Fitting and cure times are unaffected by the presence of the coating.
Factory-bonded rubber or polymer trim means your replacement glass arrives ready to fit as one complete unit.
Encapsulation is a rubber or polymer gasket moulded directly onto the glass edges during manufacturing. The trim is bonded to the glass at the factory — either by injection moulding, PU robot extrusion, or adhesive bonding. When you need a replacement, the entire panel arrives with its trim already attached, so the glass and gasket are replaced together as a single unit rather than as separate components.
Check your current windscreen or rear window edges. If you see a continuous rubber or polymer seal running around the perimeter that appears moulded or permanently bonded to the glass itself — rather than a separate trim clipped or screwed to the frame — your glass is encapsulated. Ask your dealer or service centre to confirm; they can also check your vehicle specification sheet.
Encapsulated glass simplifies replacement because there's no separate trim to remove, refit, or source. The bonded gasket is replaced as part of the glass unit, which reduces installation complexity and potential leak points. Cure time and drive-away procedures remain unchanged. No additional sourcing delays — encapsulated replacements are stocked as complete assemblies by most suppliers.
Heated windscreens use embedded wires to quickly clear ice and condensation in cold weather.
A heated windscreen is integrated with a fine mesh of electrical wires embedded within the glass itself. When activated, these wires generate heat to warm the windscreen surface, helping to rapidly clear frost, ice, and condensation during cold or damp conditions. This feature improves visibility and safety in winter driving and reduces reliance on engine heat and demister air, which can be slower on very cold mornings.
Check your vehicle's handbook or contact your dealership service centre — they can confirm whether your model includes this feature. Look for a dashboard symbol (usually a windscreen icon with heat waves) when you activate the function, or check your infotainment settings for a heating or climate option linked to the windscreen. Some vehicles have a dedicated button on the stalk or console.
Heated windscreens require replacement glass to be of the correct heated specification — standard unheated glass cannot be fitted. The replacement glass must be sourced to match your vehicle's exact heated-wire configuration. Installation is straightforward, though the technician will confirm the heating element is functioning correctly after fitting. No calibration is required for this feature.
A defogging detector automatically clears condensation from your windscreen, improving visibility in damp conditions.
A defogging detector is a sensor that monitors moisture levels on the windscreen and triggers the demister system automatically when condensation builds up. It improves driver visibility and safety in damp or cold weather by preventing manual intervention. The sensor typically sits near the rear-view mirror, positioned to sense moisture accumulation on the glass surface.
Check your vehicle's handbook or ask your dealer's service centre whether your model includes an automatic defogging or moisture-sensing demister. Look near the rear-view mirror for a small sensor unit. Some vehicles display an indicator light or message on the dashboard when the system is active.
The defogging detector does not affect windscreen replacement or require recalibration after fitting. The sensor itself remains in place and continues to function once the new windscreen is installed. No additional calibration, cure time, or specialist procedures are needed.
The moulded trim that surrounds your camera and sensor cluster at the top of the windscreen, typically transferred or supplied with replacement glass.
A bracket for safety features is the moulded plastic or composite shroud that sits at the top of the windscreen, framing and protecting the camera and sensor cluster mounted behind the rear-view mirror. This trim cover houses forward-facing driver-assistance cameras and sensors — equipment that monitors the road ahead for lane-keeping, collision warning, adaptive cruise control, and similar safety functions. The bracket itself is part of the vehicle's structural frame, but the trim cover you see is what protects and aesthetically integrates the technology into the windscreen area.
Look at the top centre of your windscreen, just above or around the rear-view mirror. If you see a dark moulded shroud or trim panel — often rectangular or tapered — with a visible lens or sensor window, your vehicle has a bracket for safety features. Your service history or handbook will list any ADAS (Advanced Driver Assistance System) technologies fitted. Ask your dealer or service centre if your vehicle has forward-facing cameras or sensors; if it does, you have a bracket for safety features.
On windscreen replacement, the trim cover is typically transferred from your old glass to the new one, or supplied pre-integrated with the replacement depending on the variant. This means minimal disruption to your safety system during the swap. However, if the bracket requires recalibration after glass replacement — which depends on your specific vehicle and camera type — the job may require static calibration (using a target board) or dynamic calibration (a road drive). We confirm the exact calibration procedure when we look up your vehicle.
We confirm the exact procedure for your specific vehicle when you book.
A camera mounted near the rear-view mirror monitors the road ahead for lane-keep and traffic-sign features.
A forward-facing camera positioned in the windscreen header area (typically mounted on or near the rear-view mirror bracket) captures video of the road ahead. This camera feeds data to driver-assistance systems such as lane-departure warning, lane-keep assist, autonomous emergency braking, and traffic-sign recognition. The camera is a core component of modern ADAS (Advanced Driver Assistance Systems) and requires precise alignment after windscreen replacement to ensure these safety features function correctly.
Look for a small dark triangular or lens-shaped component mounted in the black plastic trim area above the windscreen, typically centred near the rear-view mirror or slightly to one side. Your vehicle's handbook or infotainment menu may reference 'Lane Assist', 'Traffic Sign Recognition', or 'Autonomous Emergency Braking'. Ask your dealer or service centre directly if your car is equipped with a forward-facing camera system.
Windscreen replacement on camera-equipped vehicles requires calibration of the camera system after the new glass is fitted. The exact calibration procedure—whether static (using a target board in a controlled environment) or dynamic (road-based)—varies by vehicle make, model, and year. We confirm the precise calibration requirement when we look up your specific vehicle. Calibration ensures lane-keep, sign recognition, and emergency-braking systems function safely. This may extend the fitting schedule and may necessitate workshop-based fitting rather than mobile attendance.
We confirm the exact procedure for your specific vehicle when you book.
A Head-Up Display projects your speed, navigation cues and key alerts onto the windscreen so you can read them without looking down.
A Head-Up Display (HUD) projects driving information — speed, navigation cues, ADAS alerts — onto the windscreen in your line of sight, so you can read it without taking your eyes off the road. The projector is mounted in the dashboard and shines the image upwards onto a special HUD-compatible windscreen that uses a wedge-shaped laminate to prevent a ghost image. The image typically appears to float a few feet ahead of the car. Common on premium and sports models, increasingly standard on mid-range cars from the 2020s onwards.
Check your vehicle's specification sheet or handbook under 'display features' or 'HUD'. Look for a small projector unit mounted on the dashboard, typically below the steering wheel or in the instrument cluster area. When you start the vehicle, a bright image should appear on the lower windscreen area. Your dealer's service centre can confirm whether your specific model and trim level includes a HUD.
Your replacement windscreen needs to be HUD-compatible — built with the correct wedge laminate so the projected image stays sharp and double-free. Once the HUD-compatible glass is fitted, the projector itself typically doesn't need recalibration: image position is user-adjustable via your dashboard controls. We confirm your vehicle uses the HUD-compatible windscreen variant when ordering, so the replacement matches the original.
Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.
Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.
The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.
Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.
Heat-absorbing PVB interlayer reduces solar gain and cabin temperature on warm days—but must match your original spec.
Heat-absorbing PVB is a specially formulated interlayer sandwiched between the glass plies in your windscreen. It absorbs a portion of the sun's infrared radiation before it enters the cabin, reducing solar heat gain on warm days. This keeps the interior cooler and reduces air-conditioning workload. The feature is built into the glass during manufacture and cannot be added or removed after production. If your vehicle left the factory with this interlayer, any replacement windscreen must carry the same PVB specification to maintain the original thermal performance.
Check your vehicle's specification sheet or handbook—heat-absorbing PVB is listed under windscreen or glass specification. You can also ask your dealership service centre or provide us with your vehicle registration; we'll confirm whether your car came with this feature as standard or as an option.
Replacement windscreens with heat-absorbing PVB must be sourced to the exact OE specification—aftermarket alternatives with standard PVB will not deliver the same solar-control performance. We ensure the correct spec is ordered before the fit. No calibration is required. Installation and cure procedures are identical to standard windscreen replacement; the interlayer is integral to the glass and requires no additional treatment.
The Range Rover L405 (2010–present) spans two distinct generations with progressively sophisticated windscreen engineering. Early models carry straightforward laminated windscreens with rain sensors and acoustic interlayers, while later L405s from around 2015 onwards feature enhanced thermal coatings, encapsulated trim, and heated glass options.
From the mid-2010s, Land Rover's InControl driver assistance suite introduced front-facing camera systems to the L405 range. Models equipped with Lane Keep Assist, Lane Departure Warning, or Forward Collision Warning carry a mono camera mounted at the windscreen — meaning windscreen replacement requires static calibration by a technician with the right equipment.
Own a different Land Rover? We've got you — every variant, every year.
The questions customers ask us most often.
