Instant quote across all Audi e-Tron variants in under 60 seconds, fitted by approved fitters — booked in under two minutes.
Make
Audi
Model
e-Tron
No card required · Free to quote
Price variation is driven primarily by ADAS calibration complexity and the encapsulated glass specification. All e-Tron windscreens carry the same core safety features — camera bracket, rain sensor, acoustic glass — so differences are modest and reflect mainly the technician's workshop setup and calibration equipment. Early-production variants and later models carry the same specification, keeping pricing consistent across the range.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2026 | £765 — £1,002 | 2 variants | Price my 2026 |
| 2025 | £765 — £1,002 | 2 variants | Price my 2025 |
| 2024 | £765 — £1,002 | 2 variants | Price my 2024 |
| 2023 | £765 — £1,002 | 2 variants | Price my 2023 |
| 2022 | £765 — £1,002 | 2 variants | Price my 2022 |
| 2021 | £765 — £1,002 | 2 variants | Price my 2021 |
| 2020 | £765 — £1,002 | 2 variants | Price my 2020 |
| 2019 | £765 — £1,002 | 2 variants | Price my 2019 |
| 2018 | £765 — £1,002 | 2 variants | Price my 2018 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older e-Trons can still be booked.
Curious why prices vary so widely? Read our UK windscreen replacement cost guide .
Reviews below are hand-picked from recent UK customers. Across the whole of UK Car Glass, 4.81/5 from 1,468 Trustpilot reviews.
Booking your e-Tron windscreen replacement takes three simple stages: quote, parts check, and fitting day.
Use our online widget to answer a few quick questions about your e-Tron (year, trim, and any interior features you remember). A quote is ready in under 60 seconds.
Once you book, our parts-check team confirms your exact windscreen variant — matched to your factory specification including the camera bracket, rain sensor, and acoustic glass.
An approved fitter in your area is matched to your job. For e-Tron windscreens, the fitting is scheduled at a workshop so that static camera calibration can be completed in a controlled environment after the glass is set.
On fitting day, the fitter removes your damaged windscreen, fits the replacement, and completes static camera calibration using diagnostic targets. Calibration runs in parallel with adhesive cure.
Your fitter confirms the minimum drive-away time before you leave — typically the same as a non-ADAS job because cure and calibration happen simultaneously.
Your replacement comes with a two-year warranty on workmanship and glass quality.
From quote to booking takes under two minutes; the full job is typically completed within a couple of hours.
All e-Tron windscreen replacements are fitted at a workshop rather than mobile at your address. The reason is static camera calibration — this ADAS system requires printed target boards placed at specific distances in a controlled environment, which cannot be done safely on a driveway or car park.
The entire job (windscreen replacement plus calibration) is scheduled at one location, so there is no split appointment. Calibration runs in parallel with adhesive cure, so it does not add to your minimum drive-away time.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
Acoustic glass reduces cabin noise for a quieter, more comfortable ride.
Acoustic windscreen glass is laminated with a special acoustic interlayer that absorbs and dampens sound vibrations. It reduces exterior noise—from traffic, wind, and road surface—before it enters the passenger compartment. This makes the cabin noticeably quieter and creates a more peaceful driving experience. It's a comfort feature, not a safety one; standard laminated windscreens already meet impact safety requirements.
Check your windscreen for an ear symbol, the word 'Acoustic', a capital 'A', or the term 'SoundScreen' printed in one of the four corners. These markings indicate acoustic-grade glass. You can also ask your vehicle's dealership or service centre whether your model came fitted with acoustic glass—it's often a factory option on comfort or premium trims.
Acoustic glass is always laminated and bonds to the frame like any standard windscreen, so replacement follows the normal bonded-glass procedure. No specialist calibration is required. The replacement technician will fit it using standard adhesive and sealant. Cure time and drive-away restrictions are identical to standard laminated windscreens. Acoustic glass is widely available as an aftermarket OE-equivalent option.
The moulded trim that surrounds your camera and sensor cluster at the top of the windscreen, typically transferred or supplied with replacement glass.
A bracket for safety features is the moulded plastic or composite shroud that sits at the top of the windscreen, framing and protecting the camera and sensor cluster mounted behind the rear-view mirror. This trim cover houses forward-facing driver-assistance cameras and sensors — equipment that monitors the road ahead for lane-keeping, collision warning, adaptive cruise control, and similar safety functions. The bracket itself is part of the vehicle's structural frame, but the trim cover you see is what protects and aesthetically integrates the technology into the windscreen area.
Look at the top centre of your windscreen, just above or around the rear-view mirror. If you see a dark moulded shroud or trim panel — often rectangular or tapered — with a visible lens or sensor window, your vehicle has a bracket for safety features. Your service history or handbook will list any ADAS (Advanced Driver Assistance System) technologies fitted. Ask your dealer or service centre if your vehicle has forward-facing cameras or sensors; if it does, you have a bracket for safety features.
On windscreen replacement, the trim cover is typically transferred from your old glass to the new one, or supplied pre-integrated with the replacement depending on the variant. This means minimal disruption to your safety system during the swap. However, if the bracket requires recalibration after glass replacement — which depends on your specific vehicle and camera type — the job may require static calibration (using a target board) or dynamic calibration (a road drive). We confirm the exact calibration procedure when we look up your vehicle.
We confirm the exact procedure for your specific vehicle when you book.
Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.
Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.
The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.
Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.
A single camera mounted near the rear-view mirror that helps with lane-keeping and collision avoidance.
A mono camera is a single-lens camera positioned behind the windscreen, typically in the upper centre area near the rear-view mirror. It captures the road ahead and uses computer vision to detect lane markings, vehicles, and road hazards. The camera feeds data to driver-assistance systems such as lane-keeping assist, lane-departure warning, and forward-collision warning. It forms the visual foundation of these safety features, allowing the vehicle to monitor road position and surrounding traffic automatically.
Look in the black trim area above the windscreen, centred behind the rear-view mirror — you will see a small triangular lens assembly or dark lens cover. Check your vehicle handbook or ask your dealer's service department to confirm your model has lane-assistance or collision-warning features; vehicles with these systems almost always have a mono camera. Dashboard warning symbols related to lane or collision systems also indicate the presence of this camera.
When the windscreen is replaced, the camera bracket and lens assembly must be removed and carefully repositioned on the new glass. The camera may require calibration after fitting to ensure accurate road detection and lane recognition. Calibration needs vary by vehicle — we confirm the exact procedure when we look up your specific vehicle. The job may take longer than a standard windscreen replacement, and workshop facilities may be required if calibration demands a controlled environment.
We confirm the exact procedure for your specific vehicle when you book.
Your wipers automatically activate when rain falls on the windscreen.
A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.
Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.
Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.
Heated zones around sensors prevent frost and moisture buildup, helping your safety systems work reliably.
A sensor heated zone is an electrical heating element integrated into or around camera, radar, or sensor mounts on the windscreen. Its purpose is to prevent frost, ice, condensation, and moisture accumulation on sensor lenses and housings. This keeps safety systems — such as lane-keeping assist, collision warning, and adaptive cruise control — functioning accurately in cold, wet, or foggy conditions. Without this heating, moisture or ice can obscure sensors and cause them to malfunction or deactivate.
Check your vehicle's handbook for mention of 'heated sensor zone' or 'sensor heating' in the windscreen or ADAS section. Look at the top edge of your windscreen where cameras or radar modules are mounted — you may see small heating elements or wiring near these components. Ask your dealership or service centre directly: they can confirm whether your specific model includes sensor heating as standard.
Windscreens with heated sensor zones require careful handling during replacement to preserve the heating element and its electrical connections. The heating circuit must be reconnected properly after the new glass is fitted. Depending on the vehicle, this may involve static or dynamic camera calibration after installation. We confirm the exact procedure — including any calibration needs — when we look up your vehicle details.
We confirm the exact procedure for your specific vehicle when you book.
Static calibration uses printed targets indoors to align your forward-facing camera after windscreen replacement.
Static camera calibration is a procedure in which a forward-facing camera system is realigned using printed target boards positioned at manufacturer-specified distances and heights in front of the vehicle. The vehicle remains stationary indoors throughout. A diagnostic tool reads the camera's view of these targets and adjusts the camera's alignment to factory specification. This ensures the camera can accurately detect road features, lane markings, pedestrians, and other objects — critical for driver-assistance systems like lane-keeping, collision warning, and adaptive cruise control to function safely and reliably.
Check your vehicle's handbook or ask your dealer's service centre whether your car has a forward-facing camera system that requires calibration after windscreen replacement. Look for driver-assistance features like lane-keeping assist, autonomous emergency braking, or adaptive cruise control on the dashboard menu.
When a windscreen with an integrated or bracket-mounted camera is replaced, the camera's alignment can shift. Static calibration realigns the camera using indoor target boards, which must be performed in a workshop environment where printed targets can be positioned and secured at precise distances. This procedure is conducted after the windscreen is fitted and bonded. The workshop booking accommodates the additional time required for calibration, and we apply the no-split policy — both replacement and calibration happen at the same location on the same visit.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
A Head-Up Display projects your speed, navigation cues and key alerts onto the windscreen so you can read them without looking down.
A Head-Up Display (HUD) projects driving information — speed, navigation cues, ADAS alerts — onto the windscreen in your line of sight, so you can read it without taking your eyes off the road. The projector is mounted in the dashboard and shines the image upwards onto a special HUD-compatible windscreen that uses a wedge-shaped laminate to prevent a ghost image. Common on premium and sports models, increasingly standard on mid-range cars from the 2020s onwards.
Check your vehicle's specification sheet or handbook under 'display features' or 'HUD'. Look for a small projector unit mounted on the dashboard, typically below the steering wheel or in the instrument cluster area. When you start the vehicle, a bright image should appear on the lower windscreen area. Your dealer's service centre can confirm whether your specific model and trim level includes a HUD.
Your replacement windscreen needs to be HUD-compatible — built with the correct wedge laminate so the projected image stays sharp and double-free. Once the HUD-compatible glass is fitted, the projector itself typically doesn't need recalibration: image position is user-adjustable via your dashboard controls. We confirm your vehicle uses the HUD-compatible windscreen variant when ordering, so the replacement matches the original.
The Audi e-Tron has been in production since 2018, establishing itself as Audi's flagship electric SUV. All variants across the range feature a green-tinted laminated windscreen with rain sensors and acoustic noise-reduction glass — a standard specification reflecting the model's premium positioning.
Every e-Tron windscreen includes a bracket for the forward-facing safety camera, which supports Audi pre sense front, active lane assist, adaptive cruise assist, and traffic sign recognition. A VIN notch is also present on all variants, and the sensor heated zone prevents moisture ingress into the camera assembly.
Static camera calibration is required after windscreen replacement on all e-Tron models. This is performed indoors at a workshop with the vehicle stationary, using printed targets placed at manufacturer-specified distances and heights. The calibration runs in parallel with adhesive cure, so it does not extend your minimum drive-away time — though the fitting itself takes longer than a non-ADAS windscreen.
Own a different Audi? We've got you — every variant, every year.
The questions customers ask us most often.
