Wayne P.
C-HR ownerTrustpilot31 May 2025
Toyota C-HR
Great value
Friendly technician and very efficient
Instant quote across Toyota C-HR windscreen variants in under 60 seconds, fitted by approved fitters — booked in under two minutes.
Make
Toyota
Model
C-HR
No card required · Free to quote
Prices vary primarily with ADAS equipment and calibration requirements. Earlier C-HR models without camera systems are the most affordable, whilst later variants equipped with Toyota Safety Sense and requiring static calibration after fitting carry higher overall costs due to the additional workshop time and diagnostic work involved.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2026 | £305 — £821 | 4 variants | Price my 2026 |
| 2025 | £305 — £821 | 4 variants | Price my 2025 |
| 2024 | £305 — £821 | 4 variants | Price my 2024 |
| 2023 | £305 — £821 | 5 variants | Price my 2023 |
| 2022 | £305 — £778 | 4 variants | Price my 2022 |
| 2021 | £305 — £778 | 5 variants | Price my 2021 |
| 2020 | £305 — £743 | 3 variants | Price my 2020 |
| 2019 | £305 — £759 | 4 variants | Price my 2019 |
| 2018 | £305 — £759 | 4 variants | Price my 2018 |
| 2017 | £305 — £759 | 4 variants | Price my 2017 |
| 2016 | £305 — £759 | 4 variants | Price my 2016 |
| 2015 | £759 — £759 | 1 variant | Price my 2015 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older C-HRs can still be booked.
Showing 1 review from verified Toyota C-HR owners. Across the whole of UK Car Glass, 4.82/5 from 1,493 Trustpilot reviews.
Your replacement windscreen is sourced to match your exact factory specification and fitted by a specialist technician in your area.
Instant online quote — answer a few quick questions about your C-HR's trim and features to receive a personalised price in under 60 seconds.
Complete your booking online in under two minutes, selecting your preferred date and time.
Our parts-check team verifies your windscreen variant and confirms any ADAS calibration requirements before the technician is assigned.
On fitting day, the specialist arrives at your home or workshop (depending on whether calibration is needed), removes the old glass, and installs your replacement.
For ADAS-equipped variants, static camera calibration runs in parallel with adhesive cure — your fitter confirms the drive-away time before leaving.
You're covered by a two-year warranty on the replacement and workmanship.
From booking to the road, the entire process is guided by our network of trusted specialists, backed by Trustpilot reviews.
Most C-HR windscreen replacements can be fitted at your home or preferred location as a mobile service. However, if your variant requires static camera calibration after fitting, the entire job is scheduled at a workshop — replacement and calibration happen in one visit to ensure the system is correctly aligned before you drive away.
This single-location approach guarantees calibration is completed and documented, keeping your safety systems functioning as intended.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
On the Toyota C-HR: fitted on every one of the 7 windscreen variants we list; model years 2015–2026.
Laminated glass with noise-dampening interlayers — reduces road and wind noise inside the cabin.
Fitted as standard across all C-HR windscreens in our catalogue from 2015 onwards. Confirmed during the quote.
On the Toyota C-HR: fitted on every one of the 7 windscreen variants we list; model years 2015–2026.
Factory green tint applied to the windscreen glass — standard across all Toyota vehicles for UV and heat reduction.
All C-HR windscreens carry the green tint to match the original specification; confirmed at the quote stage.
On the Toyota C-HR: fitted on every one of the 7 windscreen variants we list; model years 2015–2026.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
On the Toyota C-HR: fitted on 5 of the 7 windscreen variants we list (71%); model years 2015–2026; calibration varies by vehicle.
Forward-facing mono camera mounted behind the windscreen for Toyota Safety Sense collision avoidance and lane-keeping features.
Present on all active C-HR variants; most common from 2018 onwards as Toyota Safety Sense became standard.
On the Toyota C-HR: fitted on 5 of the 7 windscreen variants we list (71%); model years 2015–2026; no calibration after replacement.
Automatic wiper trigger — detects moisture on the windscreen and activates wipers without driver input.
Fitted on higher-specification and newer C-HR variants; check your owner's manual or confirm during the quote if unsure.
On the Toyota C-HR: fitted on 1 of the 7 windscreen variants we list (14%); model years 2016–2021.
An aerial laminated into the windscreen or rear window restores radio, DAB or TV reception without a roof-mounted mast.
An antenna is a conductive print laminated into the glass during manufacture, typically used for radio, DAB (digital audio broadcasting) or television reception. It replaces the traditional roof-mounted aerial mast found on older vehicles. The antenna is integrated into the glass interlayer and connected to the vehicle's receiver unit via a connector embedded in the glass edge. This design offers a cleaner aesthetic, reduces wind noise, and eliminates the vulnerability of a protruding mast to damage or theft.
Check your vehicle's roof — if there is no visible aerial mast, your car likely has a laminated antenna. You can also ask your dealer or service centre whether your windscreen or rear window carries an antenna print. The connector may be visible on the glass edge or inside the door frame trim.
When replacing glass with a laminated antenna, the replacement must carry the matching antenna print and connector to restore reception immediately on fitting. Aftermarket or original-equipment glass with the correct antenna specification is essential; a plain replacement will leave you without radio or DAB signal. Our fitters verify the antenna specification during booking and source the correct variant before the appointment.
On the Toyota C-HR: fitted on 1 of the 7 windscreen variants we list (14%); model years 2016–2021; calibration varies by vehicle.
Moulded shroud surrounding the camera and sensor cluster at the top of the windscreen, holding the ADAS hardware in alignment.
Present on newer Safety Sense-equipped models; the trim is typically transferred from your old windscreen to the replacement or supplied pre-integrated with the new glass.
On the Toyota C-HR: fitted on 1 of the 7 windscreen variants we list (14%); model years 2016–2026.
Heated windscreens use embedded wires to quickly clear ice and condensation in cold weather.
A heated windscreen is integrated with a fine mesh of electrical wires embedded within the glass itself. When activated, these wires generate heat to warm the windscreen surface, helping to rapidly clear frost, ice, and condensation during cold or damp conditions. This feature improves visibility and safety in winter driving and reduces reliance on engine heat and demister air, which can be slower on very cold mornings.
Check your vehicle's handbook or contact your dealership service centre — they can confirm whether your model includes this feature. Look for a dashboard symbol (usually a windscreen icon with heat waves) when you activate the function, or check your infotainment settings for a heating or climate option linked to the windscreen. Some vehicles have a dedicated button on the stalk or console.
Heated windscreens require replacement glass to be of the correct heated specification — standard unheated glass cannot be fitted. The replacement glass must be sourced to match your vehicle's exact heated-wire configuration. Installation is straightforward, though the technician will confirm the heating element is functioning correctly after fitting. No calibration is required for this feature.
On the Toyota C-HR: fitted on 1 of the 7 windscreen variants we list (14%); model years 2016–2026.
Heating elements embedded in the glass melt ice from your wipers and the bottom of your windscreen.
A heated wiper rest area uses electric heating elements embedded into the windscreen in the area where your wipers park when not in use. These elements warm the glass to prevent ice and frost from bonding to the wiper blades and the lower windscreen edge during cold weather. This reduces the effort needed to clear ice in the morning and helps protect your wipers from damage caused by frozen adhesion to the glass.
Check your windscreen's lower edge where the wipers rest — you may see faint heating lines or elements visible in the glass. Your handbook or service history will confirm the feature. You can also ask your dealer or service centre whether your vehicle is equipped with a heated wiper rest area.
When replacing a windscreen with a heated wiper rest area, the replacement glass must include the heating elements. Aftermarket and OE glazing suppliers offer this feature, but availability varies by vehicle. The heating system does not require calibration after replacement, though the technician will ensure the heating element connections are properly restored during installation.
On the Toyota C-HR: fitted on 1 of the 7 windscreen variants we list (14%); model years 2016–2021; calibration varies by vehicle.
A single camera mounted near the rear-view mirror that helps with lane-keeping and collision avoidance.
A mono camera is a single-lens camera positioned behind the windscreen, typically in the upper centre area near the rear-view mirror. It captures the road ahead and uses computer vision to detect lane markings, vehicles, and road hazards. The camera feeds data to driver-assistance systems such as lane-keeping assist, lane-departure warning, and forward-collision warning. It forms the visual foundation of these safety features, allowing the vehicle to monitor road position and surrounding traffic automatically.
Look in the black trim area above the windscreen, centred behind the rear-view mirror — you will see a small triangular lens assembly or dark lens cover. Check your vehicle handbook or ask your dealer's service department to confirm your model has lane-assistance or collision-warning features; vehicles with these systems almost always have a mono camera. Dashboard warning symbols related to lane or collision systems also indicate the presence of this camera.
When the windscreen is replaced, the camera bracket and lens assembly must be removed and carefully repositioned on the new glass. The camera may require calibration after fitting to ensure accurate road detection and lane recognition. Calibration needs vary by vehicle — we confirm the exact procedure when we look up your specific vehicle. The job may take longer than a standard windscreen replacement, and workshop facilities may be required if calibration demands a controlled environment.
The Toyota C-HR has been in production since 2015, establishing itself as a popular compact crossover across European markets. Early models feature straightforward laminated windscreens with green tinting, whilst later variants introduce acoustic interlayers for improved cabin noise reduction.
From around 2018 onwards, Toyota Safety Sense became increasingly standard across the C-HR lineup, bringing forward-facing cameras for collision avoidance and adaptive cruise. This means most C-HR windscreens in our catalogue require camera bracket accommodation and, on some variants, static camera calibration after replacement.
Acoustic glass is fitted across the entire range, and all variants carry the factory green tint to match the original specification. Rain sensors appear on around 60% of active variants, adding automated wiper convenience to the ownership experience.
Own a different Toyota? We've got you — every variant, every year.
The questions customers ask us most often.