Instant quote across all Citroën DS3 Crossback variants in under 60 seconds, fitted by approved fitters — booked in under two minutes.
Make
Citroen
Model
DS3 Crossback
No card required · Free to quote
Pricing varies primarily based on the fitted ADAS equipment and calibration complexity. Earlier 2018–2019 models typically carry standard driver assistance, while later variants with the full Safety Pack Plus suite — which combines video and radar assistance — may incur slightly higher calibration costs. Acoustic glass and encapsulated trim are fitted across all variants, so variation is minimal compared to some rivals.
| Year | Price range | Variants | Quote |
|---|---|---|---|
| 2022 | £681 — £766 | 2 variants | Price my 2022 |
| 2021 | £681 — £766 | 2 variants | Price my 2021 |
| 2020 | £681 — £681 | 1 variant | Price my 2020 |
| 2019 | £681 — £681 | 1 variant | Price my 2019 |
| 2018 | £681 — £681 | 1 variant | Price my 2018 |
The displayed range is an indicator — the final price is produced by the quote form after you confirm your variant. Older DS3 Crossbacks can still be booked.
Curious why prices vary so widely? Read our UK windscreen replacement cost guide .
Reviews below are hand-picked from recent UK customers. Across the whole of UK Car Glass, 4.82/5 from 1,422 Trustpilot reviews.
Booking your DS3 Crossback windscreen replacement follows a straightforward guided process.
Answer a quick quiz about your vehicle (make, model, year, features) — no registration needed — to identify your exact windscreen variant.
Receive an instant quote based on glass specification, ADAS equipment, and your location.
Complete your booking online in under two minutes; you'll be matched with a local technician from our network.
Your fitter arranges a convenient time (mobile at your home or at a workshop, depending on calibration needs).
On the day, the windscreen is replaced and ADAS camera calibration is completed — typically within a couple of hours.
Your fitter confirms the minimum drive-away time before you leave, and your two-year warranty begins.
All work is backed by a two-year warranty covering workmanship and glass quality.
All DS3 Crossback variants from 2018 onwards carry a front camera system requiring static calibration after windscreen replacement. This calibration uses fixed target boards and must be completed in a controlled workshop environment, so your fitting is scheduled at a workshop location rather than mobile at your home. The no-split rule means the entire job — replacement and calibration — happens in one place on one day.
Workshop fitting actually works in your favour: you're in a professional environment where our technician has full equipment access, and calibration is completed to the highest standard before you drive away.
We confirm the specific answer for your vehicle when you book.
Tap a feature to see what it is, how to spot it on your car, and how it affects glass replacement. We confirm the exact match for your vehicle when you book.
Acoustic glass reduces cabin noise for a quieter, more comfortable ride.
Acoustic windscreen glass is laminated with a special acoustic interlayer that absorbs and dampens sound vibrations. It reduces exterior noise—from traffic, wind, and road surface—before it enters the passenger compartment. This makes the cabin noticeably quieter and creates a more peaceful driving experience. It's a comfort feature, not a safety one; standard laminated windscreens already meet impact safety requirements.
Check your windscreen for an ear symbol, the word 'Acoustic', a capital 'A', or the term 'SoundScreen' printed in one of the four corners. These markings indicate acoustic-grade glass. You can also ask your vehicle's dealership or service centre whether your model came fitted with acoustic glass—it's often a factory option on comfort or premium trims.
Acoustic glass is always laminated and bonds to the frame like any standard windscreen, so replacement follows the normal bonded-glass procedure. No specialist calibration is required. The replacement technician will fit it using standard adhesive and sealant. Cure time and drive-away restrictions are identical to standard laminated windscreens. Acoustic glass is widely available as an aftermarket OE-equivalent option.
The moulded trim that surrounds your camera and sensor cluster at the top of the windscreen, typically transferred or supplied with replacement glass.
A bracket for safety features is the moulded plastic or composite shroud that sits at the top of the windscreen, framing and protecting the camera and sensor cluster mounted behind the rear-view mirror. This trim cover houses forward-facing driver-assistance cameras and sensors — equipment that monitors the road ahead for lane-keeping, collision warning, adaptive cruise control, and similar safety functions. The bracket itself is part of the vehicle's structural frame, but the trim cover you see is what protects and aesthetically integrates the technology into the windscreen area.
Look at the top centre of your windscreen, just above or around the rear-view mirror. If you see a dark moulded shroud or trim panel — often rectangular or tapered — with a visible lens or sensor window, your vehicle has a bracket for safety features. Your service history or handbook will list any ADAS (Advanced Driver Assistance System) technologies fitted. Ask your dealer or service centre if your vehicle has forward-facing cameras or sensors; if it does, you have a bracket for safety features.
On windscreen replacement, the trim cover is typically transferred from your old glass to the new one, or supplied pre-integrated with the replacement depending on the variant. This means minimal disruption to your safety system during the swap. However, if the bracket requires recalibration after glass replacement — which depends on your specific vehicle and camera type — the job may require static calibration (using a target board) or dynamic calibration (a road drive). We confirm the exact calibration procedure when we look up your vehicle.
A camera mounted near the rear-view mirror monitors the road ahead for lane-keep and traffic-sign features.
A forward-facing camera positioned in the windscreen header area (typically mounted on or near the rear-view mirror bracket) captures video of the road ahead. This camera feeds data to driver-assistance systems such as lane-departure warning, lane-keep assist, autonomous emergency braking, and traffic-sign recognition. The camera is a core component of modern ADAS (Advanced Driver Assistance Systems) and requires precise alignment after windscreen replacement to ensure these safety features function correctly.
Look for a small dark triangular or lens-shaped component mounted in the black plastic trim area above the windscreen, typically centred near the rear-view mirror or slightly to one side. Your vehicle's handbook or infotainment menu may reference 'Lane Assist', 'Traffic Sign Recognition', or 'Autonomous Emergency Braking'. Ask your dealer or service centre directly if your car is equipped with a forward-facing camera system.
Windscreen replacement on camera-equipped vehicles requires calibration of the camera system after the new glass is fitted. The exact calibration procedure—whether static (using a target board in a controlled environment) or dynamic (road-based)—varies by vehicle make, model, and year. We confirm the precise calibration requirement when we look up your specific vehicle. Calibration ensures lane-keep, sign recognition, and emergency-braking systems function safely. This may extend the fitting schedule and may necessitate workshop-based fitting rather than mobile attendance.
Factory-bonded rubber or polymer trim means your replacement glass arrives ready to fit as one complete unit.
Encapsulation is a rubber or polymer gasket moulded directly onto the glass edges during manufacturing. The trim is bonded to the glass at the factory — either by injection moulding, PU robot extrusion, or adhesive bonding. When you need a replacement, the entire panel arrives with its trim already attached, so the glass and gasket are replaced together as a single unit rather than as separate components.
Check your current windscreen or rear window edges. If you see a continuous rubber or polymer seal running around the perimeter that appears moulded or permanently bonded to the glass itself — rather than a separate trim clipped or screwed to the frame — your glass is encapsulated. Ask your dealer or service centre to confirm; they can also check your vehicle specification sheet.
Encapsulated glass simplifies replacement because there's no separate trim to remove, refit, or source. The bonded gasket is replaced as part of the glass unit, which reduces installation complexity and potential leak points. Cure time and drive-away procedures remain unchanged. No additional sourcing delays — encapsulated replacements are stocked as complete assemblies by most suppliers.
Green tint reduces glare and improves visual comfort by filtering certain light wavelengths.
Green tint is a light-filtering coating applied to the glass during manufacture. It absorbs and reduces transmission of certain wavelengths of light, primarily to cut glare from sunlight and reflections. The tint is subtle — often barely visible to the naked eye — but measurably improves visual comfort during prolonged driving, particularly in bright conditions. It's a factory specification chosen by the vehicle manufacturer to balance daylight comfort with interior visibility and aesthetic consistency across all glass in the vehicle.
The easiest way to check is to roll your side window halfway down and hold a piece of white paper behind it. Look carefully for a tint cast — green tint will appear as a subtle green hue compared to clear glass. Your windscreen will have the same tint as your side windows. You can also ask your vehicle's dealership or service centre — they'll have the original specification on file.
Green-tinted replacement glass must match the original tint specification to maintain visual consistency across all windows and preserve the vehicle's interior aesthetics. Aftermarket OE-equivalent (OEE) green-tinted glass is widely available, though some vehicles may require original equipment (OEM) dealership glass if the tint specification is proprietary. Tint does not affect calibration, cure time, or installation procedure — it's a cosmetic and functional specification only.
Factory-fitted brackets and mounts bonded to the glass, pre-assembled and ready to fit without sub-assembly.
Other Hardware refers to factory-fitted brackets, mounts, connectors, or trim pieces bonded permanently to the windscreen or other glass during manufacturing. These are integral to the vehicle's design but do not activate or control a specific feature — they simply secure or position components like sensors, trim strips, or mounting points. Unlike feature-specific hardware, these items are passive structural elements. A replacement carrying Other Hardware arrives pre-bonded and ready to install without additional assembly or modification.
Check your vehicle documentation or ask your dealership service centre whether your windscreen or glass panel carries factory-bonded brackets or mounts. Visual inspection may reveal trim strips, sensor housings, or antenna mounts bonded to the edges or interior surface of the glass. Your original invoice or parts list will specify if Other Hardware is present.
Replacement glass carrying Other Hardware must be sourced as a complete assembly — the brackets and mounts come pre-bonded from the supplier and cannot be transferred from the old glass. Installation is straightforward: the fitter removes the old glass and fits the replacement with its hardware already in place. No additional sub-assembly, bonding, or recalibration of the hardware itself is required. Fitting time is unaffected.
Your wipers automatically activate when rain falls on the windscreen.
A rain sensor is a device mounted on or behind the windscreen that detects moisture and triggers the wiper system automatically. The sensor uses infrared light to measure water droplets on the glass surface and signals the vehicle's electrical system to engage the wipers without driver input. This feature improves safety in sudden downpours and reduces driver workload in variable weather conditions.
Check your windscreen for a small sensor unit, usually mounted near the top centre behind the glass or at the base of the mirror. Look for a small dark component or lens. If your vehicle has automatic wipers that activate without you toggling the stalk, you have a rain sensor. Ask your dealer or service centre to confirm; they can check your vehicle records or wiper module settings.
Rain sensors are non-structural elements and do not require recalibration after windscreen replacement. The sensor bracket or mounting may need careful removal and reinstallation to ensure it sits correctly behind the new glass. If the sensor itself is damaged during removal, a replacement unit may be needed. Your fitter will confirm the condition and refit or replace the sensor as part of the standard replacement procedure.
A printed VIN reference box along the bottom edge of your windscreen helps identify your vehicle's chassis number at a glance.
A VIN (Vehicle Identification Number) notch is a small printed or etched box positioned along the lower edge of the windscreen that displays your vehicle's chassis number. This reference marking is a manufacturing and administrative feature, allowing quick visual identification of the vehicle without needing to consult documents. It's particularly useful for service records, insurance claims, and vehicle registration purposes. The notch itself doesn't affect the structural integrity or safety performance of the glass.
Look along the bottom edge of your windscreen — typically in one of the lower corners — for a small rectangular box containing printed digits or characters. If you're uncertain, check your vehicle's service handbook or ask your dealership or service centre to confirm whether your model includes this feature.
When your windscreen is replaced, the new glass will retain the VIN notch printed or etched by the manufacturer. This is a standard feature on replacement windscreens for compatible vehicles and requires no additional work or adjustment. The notch does not affect glass fitting, cure time, or any post-replacement calibration procedures.
The Citroën DS3 Crossback arrived in 2018 as a stylish compact SUV built on the PF1 platform, combining urban design with practical family appeal. All current variants (2018–present) feature laminated windscreens with a green tint, acoustic interlayers for noise reduction, rain sensors for automatic wiper activation, and dedicated camera brackets for driver assistance systems.
Every model in our catalogue carries a front-facing camera integrated into the windscreen assembly, supporting Citroën's Highway Driver Assist and Safety Pack Plus systems. This means post-replacement calibration is a routine part of the service — your fitter handles it as part of the job.
Own a different Citroen? We've got you — every variant, every year.
The questions customers ask us most often.
